JVC Ceiling Bracket WB-S623U User Manual

Page 3

Advertising
background image

WB-S622U Wall Mount

WB-S623U Ceiling Bracket

1.

Make a hole

To route cables through the wall, make a hole of

␾ 30 mm ( ␾ 1 1/8") in the wall.

2.

Route the safety cable and other cables

Open the cover and route the safety cable and other cables through this wall mount.
Please refer to "About Fall Prevention" for procedures to install the safety cable.
When a hole is not made in the wall, route the cables pulled to the wall stand
through the groove of the Wall Mount.

3.

Attach the wall mount to the wall

Attach the wall mount to the wall using 4 bolts (M5).

4.

Connect the safety cable.

Upon removing the camera mounting plate, attach the safety cable (not
supplied) to the interior of the top cover using the M3 screw. (Refer to "About
Fall Prevention".)
When attaching the camera mounting plate, ensure that the Front mark on the camera
mounting plate is facing a direction opposite to the Rear mark on the top cover.

5.

Install the ceiling panel assembly (for attaching TK-
C625U/E and VN-C625U)

To install, align the protruding part of the ceiling panel assembly with the ceiling panel
assembly positioning hole near the Front mark of the camera mounting plate.
Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly.

The screws are assembled to the ceiling panel assembly in such a way that
they will not come off.

1.

Make a hole in the ceiling.

To route cables through the ceiling, make a hole of

␾ 30 mm (␾ 1 1/8") in the ceiling.

2.

Route the safety cable and other cables

Route the safety cable and other cables through the ceiling bracket. Please
refer to "About Fall Prevention" for procedures to install the safety cable.
When a hole is not made in the ceiling, route the cables through the hole at
one side of the Ceiling Bracket. Remove the cap covering the hole before
routing the cables through.

3.

Mount the ceiling bracket to the ceiling.

Mount the ceiling bracket to the ceiling using 4 M4 screws.

4.

Connect the safety cable.

Upon removing the camera mounting plate, attach the safety cable (not supplied)
to the interior of the top cover using the M3 screw. (Refer to "About Fall Prevention".)
When attaching the camera mounting plate, ensure that the Front mark on the camera
mounting plate is facing a direction opposite to the Rear mark on the top cover.

5.

Install the ceiling panel assembly (for attaching TK-
C625U/E and VN-C625U)

To install, align the protruding part of the ceiling panel assembly with the ceiling panel
assembly positioning hole near the Front mark of the camera mounting plate.
Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly.

The screws are assembled to the ceiling panel assembly in such a way that
they will not come off.

3.

1.

2.

3.

Cover Mounting
Screw

Cover

Camera
Mounting Plate

Ceiling Panel Assy
(for attaching
TK-C625U/E
and VN-C625U)

When a hole is not
made in the wall

Cap

C a m e r a
Mounting
Plate

Ceiling Panel Assy
(for attaching
TK-C625U/E
and VN-C625U)

2.

5.

R e i n fo r c e m e n t
Angle

5.

Ceiling Panel
Assembly
Positioning Hole

Front Mark

Protruding
Part

Rear Mark

6.

Connect the cables.

Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use.

7.

Attach the camera's ceiling mount. (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E)

Attach the camera's ceiling mount to the camera mounting plate using the 4 screws (M4 x 20 mm) supplied with the wall mount. Ensure that the
Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount.

1.

Rear Mark

Front Mark

Protruding
Part

6.

Connect the cables.

Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use.

7.

Attach the camera's ceiling mount. (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E)

Attach the camera's ceiling mount to the camera mounting plate using the 4 screws (M4 x 20 mm) supplied with the ceiling bracket. Ensure that
the Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount.

Top cover

Top cover

NOTE

NOTE

When a hole is not
made in the ceiling

Ceiling Panel
Assembly
Positioning Hole

Screws
(3 locations)

The camera may drop or images on the screen may appear shaky if the ceiling
material is not strong enough. In this case, reinforce using a reinforcement materials.

CAUTION

Screws
(3 locations)

Safety cable

Cables

The camera may drop or images on the screen may appear shaky if the ceiling
material is not strong enough. In this case, reinforce using a reinforcement materials.

CAUTION

Groove

Safety
cable

Cables

S621U/622U/623U-inst

05.3.18, 9:29 AM

3

Advertising
This manual is related to the following products: