Document Outline

• Cover page.doc
• TABLE OF CONTENT.doc
  • TABLE OF CONTENTS
• PAGE 1-2.doc
  • WARNING
• PAGE 3.doc
  • • CALIFORNIA PROPOSITION 65-WARNING
• PAGE 4.doc
  • LOCATION
• Page 5.doc
• PAGE 6.doc
• Page 7.doc
• Page 8.doc
• PAGE 9.doc
  • BATTERY INSTALLATION
  • 1. To install the battery, remove the ignition button housing.
  • 2. Insert the battery into the housing with the positive terminal facing outward.
  • 3. Replace the ignition button housing after the battery has been installed (See the image below).
• PAGE 10.doc
  • LP GAS CYLINDER REQUIREMENTS
  • (20lb. Cylinder)
  • LP GAS HOOK-UP
• PAGE 11.doc
  • PROPANE REGULATOR HOOK-UP
• PAGE 12.doc
  • INSTALLATION OF NATURAL GAS REGULATOR
  • 1. The Natural Gas regulator has been factory installed. Attach the PVC gas hose to the regulator (see drawing below).
• Page 13.doc
• PAGE 14-15.doc
  • GENERAL
    • • It is handy to keep a spray bottle of soapy water near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.
      • Disconnected liquid propane cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area.
      • The gas must be turned off at the supply cylinder when the unit is not in use.
      • If the appliance is stored indoors, the cylinder must be disconnected and removed from the appliance. Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.
• PAGE 16-17.doc
  • WARNING
  • The rotisserie motor is equipped with a plug and should be plugged directly into a properly grounded receptacle.
  • Do not cut or remove the grounding prong from this plug.
  • Keep the rotisserie motor cord away from the heated surfaces of the grill. When not in use remove and store the motor in a dry location.
• PAGE 18.doc
  • • BEFORE LIGHTING…
    • Keep a spray bottle of soapy water near the gas supply valve, and check the connections before each use.
• Page 19.doc
• PAGE 20.doc
  • TO MATCH LIGHT THE GRILL
• Page 21.doc
  • STAINLESS STEEL
  • GRILL RACK
  • GRILL BURNERS
  • GRILL BURNER REMOVAL/INSTALLATION
  • The grill burners are factory installed. To remove the main burners for cleaning,
  • 1. Locate the cotter pin at the rear of the burner on the bottom side.
  • 2. Remove the cotter pin and lift the burner out of the fire box.
  • 3. To reinstall the main burners, insert the burner over the valve assembly (See exploded view and parts list on pages 23 and 25).
  • 4. Insert the back of the burner into the hole at the rear of the fire box and reinsert the cotter pin.
  • GRILL BURNER CLEANING
• PAGE 22.doc
  • BEFORE CALLING FOR SERVICE
• PAGE 23.doc
• Page 24.doc
• PAGE 25.doc
• PAGE 26.doc
• PAGE 27-29.doc
• PAGE 30-31.doc
  • BBQ SALMON
  • Preheat the BBQ
  • BAKED CHILI CORN
  • TANGY SEAFOOD KABOBS
  • PORK CHOPS
  • BARBECUED LONDON BROIL
  • VEGETABLE KABOBS
    • FAJITAS
    • BEEF AND LAMB KABOBS
    • EGGPLANT CAVIAR
    • CHICKEN TANDOORI STYLE
    • SPARE RIBS
    • PORK ROAST
    • TURKEY
• PAGE 32.doc
  • LIMITED WARRANTY
  • MODEL # 740-0165/750-0165
  • STAINLESS STEEL BUILD-IN OUTDOOR GAS GRILL