JVC RM-P210 - Manual (Page 6)

6
INTRODUCTION
CONTROLS, CONNECTORS AND INDICATORS (CONTINUED)
! [POWER] switch
Press this switch to turn the power ON and OFF.
@ [WHITE - W.BAL B/A/PRESET] switch
This switch switches the white balance control setting be-
tween the value stored in Memory B (AUTO 2), that stored
in Memory A (AUTO 1) and the PRESET value (3200K).
When the white-balance adjustment is PRESET and the
PAINT
$ button is pressed so that the lamp in it lights up,
the white-balance adjustment is set to the Manual mode,
in which the white-balance can be adjusted with the R/B
gain controls
% .
REF. : “White Balance Adjustment” on page 18.
# [WHITE - AUTO] button (with lamp)
Press this button to start an auto white-balance adjustment
of the camera (within a second). This button is activated only
when the W.BAL switch is set to “A” or “B”.
When the camera in use has the AUTO SETUP function,
pressing and holding this button for more than a second ini-
tiates the AUTO SETUP mode and then starts the auto black-
balance and auto white-balance adjustment operations. If
the camera does not have an AUTO SETUP function, press-
ing and holding this button for more than a second starts
only the auto white-balance adjustment operation.
REF. : “White Balance Adjustment” on page 18.
● When the camera performs the auto white operation
or other AUTO SET operations, the lamp in this but-
ton normally lights up and turns off when the camera
completes the operation. If the adjustment has not
been done correctly, the LCD display shows an error
message.
● The lamp in this button also lights up when the FAW
(Full-time Auto White-balance) adjustment function of
the camera is functioning.
NOTE
$ [WHITE - PAINT] button (with lamp)
When this button is pressed so that the lamp in it lights up,
the R and B gain values can be adjusted using the R and
B controls
% . If the W.BAL switch @ is set to “A” or “B”,
the white paint adjustment (fine adjustment of the R and B
gain) can be performed using the R and B controls
% .
If the W.BAL switch @ is set to PRESET, the lamp in this
button lights up and the R and B controls can vary the R
and B gain values by a larger amount than usual
% .
% [WHITE - R/B] gain controls
R : Use this knob to fine-adjust the R gain during the white
paint operation or adjust the R gain during manual white
balance adjustment.
B : Use this knob to fine-adjust the B gain during the white
paint operation or adjust the B gain during manual white
balance adjustment.
REF. : “White Balance Adjustment” on page 18.
^ [SHUTTER] control with ON/OFF button
When this knob is pressed, the shutter speed variation func-
tion is turned alternately ON and OFF.
When the shutter speed variation is ON, the SHUTTER
lamp
& lights and turning the knob will vary the shutter
speed.
In STEP mode the shutter speed is varied in stages, fine
adjustments can be made in VARIABLE mode.
REF. : Item “5A: SHUTTER” on page 25.
When the MENU lamp * is lit, turn the knob to switch
between menu items, press the knob (to the ON position)
to select an item.
REF. : “Menu Setup Method” on page 20.
& [SHUTTER] lamp
This lamp lights up to indicate that the shutter speed vari-
ation facility is ON.
Adjust the shutter speed using the SHUTTER control
^ .
* [MENU] button (with lamp)
When this button is held depressed for about 1 second,
the button lamp is lit and the menu becomes variable. (The
SHUTTER and GAIN lamps should be off.)
Pressing this button terminates a menu and turns the lamp
in the button off.
REF. : “Menu Setup Method” on page 20.
( [F1 to F4] function keys
Each of these keys can turn the function assigned to it
alternately ON and OFF.
REF. : “Function Keys” on page 15.
) LCD display
This panel shows the SHUTTER and GAIN settings as
well as the functions assigned to the function buttons.
This panel is also used to show menus and various opera-
tion messages.
⁄ [BARS] button (with lamp)
When this button is pressed, the lamp in it lights up and
the RM-P210 outputs the color bar signal. This signal is
used during genlock operation.
REF. : “Adjustments for Genlock Operation” on page 13.
¤ [FULL AUTO] button (with lamp)
When this button is pressed, the lamp in it lights up and
the RM-P210 enters the FAS (Full-Auto Shooting) mode.
Pressing the button again turns the lamp off.
In the FAS mode, the BARS mode is switched OFF, and
the auto level control, auto iris control and full-auto white
balance control functions are performed automatically in
an integrated manner.
For details, please read the description of the FAS func-
tion in the manual of the camera in use.
The functions that can be controlled are variable depend-
ing on which camera model is connected.
REF. : “Function Available Depending on Camera
Models” on page 29.