English – JVC RX-7000RBK User Manual

Page 31

Advertising
background image

28

English

3. Press EFFECT to select an effect

level you want.

• Each time you press the button, the effect

level changes as follows:

As the number increases, the selected 3D-PHONIC mode
becomes stronger.

Adjusting the DAP Modes

Once you have adjusted the DAP modes, the adjustment is
memorized for each DAP mode.

Before you start, remember...
• Make sure that you have set the speaker information correctly

(see page 14).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You cannot adjust the rear speaker output level when you have set

“REAR SPK” to “NONE.” See page 14.

• When the DAP mode is used with the SEA mode (see page 24),

sounds may be distorted. If this happens, turn off the SEA mode.

On the front panel:

1. Press DSP MODE repeatedly until

the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.

The DSP indicator also lights up on the display.
• When you have set “REAR SPK” to “NONE,” the 3D-

PHONIC indicator also lights up.

2. Adjust the speaker output levels.

1) Press (BALANCE/) SURROUND

ADJUST repeatedly until one of the
indications appears on the display.
“REAR L LEVEL”:

To adjust the left rear speaker level.

“REAR R LEVEL”:

To adjust the right rear speaker level.

2) Turn MULTI JOG to adjust the

selected speaker output level (from –10
dB to +10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output level.

AUDIO/
TV/VCR

CATV/DBS

DSP MODE

DSP EFFECT 1

DSP EFFECT 2

DSP EFFECT 3

DSP EFFECT 4

DSP EFFECT 5

EFFECT

7

/P

MULTI JOG

BALANCE/

SURROUND

ADJUST

BALANCE/

SURROUND

ADJUST

IMPORTANT:

When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR”.

Adjusting the 3D-PHONIC Modes

Once you have adjusted the 3D-PHONIC modes, the adjustment is
memorized for each 3D-PHONIC mode.

Before you start, remember...
• Make sure that you have set the speaker information correctly

(see page 14).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On the front panel:

1. Press DSP MODE repeatedly until

“3D ACTION” or “3D
THEATER” appears on the
display.

The 3D-PHONIC, DSP and

Ÿ PRO LOGIC indicators

also light up on the display.

2. Adjust the effect level.

1) Press (BALANCE/) SURROUND

ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.

2) Turn MULTI JOG to select the effect

level.
• As you turn it, the effect level changes

as follows:

As the number increases, the selected 3D-PHONIC mode
becomes stronger.

From the remote control:

1. Press SURROUND MODE

repeatedly until “3D ACTION” or
“3D THEATER” appears on the
display.

The 3D-PHONIC, DSP, and

Ÿ PRO LOGIC indicators also

light up on the display.

2. Press SOUND.

The 10 keys are activated for sound adjustments.

MULTI JOG

DSP EFFECT 1

DSP EFFECT 2

DSP EFFECT 3

DSP EFFECT 4

DSP EFFECT 5

SURROUND

MODE

SOUND

DSP MODE

EN24_33.RX-7000R[E]/f

00.4.24, 3:02 PM

28

Advertising