JVC RX-668RBK - Manual (Page 23)

20
English
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the DAP mode — LIVE
CLUB, DANCE CLUB, HALL, or
PAVILION — appears on the
display.
The DSP and the selected DAP mode indicators also light up on
the display.
3. Press REAR•L – / + to adjust the
rear speaker output level.
• Pressing REAR•L – decreases the output
level up to –10 dB.
• Pressing REAR•L + increases the output
level up to +10 dB.
Note:
You cannot adjust the left and right rear speaker output levels
separately.
4. Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, the selected DAP mode becomes
stronger.
Adjusting the Surround Modes — Dolby
Surround and JVC Theater Surround
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 11).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You can only adjust the effect level when selecting JVC Theater
Surround.
• You can only adjust the rear and/or center speaker output levels
when you have connected rear speakers and/or a center speaker
and have set “REAR SPK” and/or “CENTER SPK” correctly. See
page 11.
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the mode — “PRO LOGIC”
or “THEATER” — appears on the
display.
• When selecting “PRO LOGIC,” the PRO LOGIC indicator
also lights up on the display.
• When selecting “THEATER,” the DSP, PRO LOGIC and
THEATER indicators also light up on the display.
3. Press TEST to check the speaker
output balance.
“TEST TONE L” starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• The speaker indicators also light on the display while the test
tone comes out of the speakers.
L: Lights when the test tone comes out of the
left front speaker.
C: Lights when the test tone comes out of the
center speaker.
R: Lights when the test tone comes out of the
right front speaker.
S: Lights when the test tone comes out of the
rear speakers.
4. Press CENTER – / + repeatedly to
adjust the center speaker output
level (from –10 to +10).
5. Press REAR•L – / + to adjust the
rear speaker output level (from
–10 to +10).
Notes:
• You cannot adjust the left and right rear speaker output levels
separately.
• You cannot use the REAR•R –/+ buttons to adjust the rear
speaker output levels.
6. Press TEST again to stop the test
tone.
7. ONLY FOR “THEATER”:
Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, JVC Theater Surround becomes
stronger.
2
TEST
S
C L R
6 5
– CENTER +
9 8
– REAR•L +
4
EFFECT
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4 DSP EFFECT 5
9 8
– REAR•L +
SOUND
CONTROL
3
SURROUND
SOUND
CONTROL
3
SURROUND
2
TEST
4
EFFECT
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4 DSP EFFECT 5
TEST TONE L
(Left front speaker)
TEST TONE S
(Rear speakers)
TEST TONE C
(Center speaker)
TEST TONE R
(Right front speaker)
EN08_22.RX-668R[E]/2 99.1.28, 1:14 PM 20