Tuner setting, Cable box and/or dbs receiver control setting, Setting channels automatically — auto channel set – JVC HR-3911U User Manual

Page 7: Setting channels manually — manual channel set

Advertising
background image

— 7 —

Tuner Setting

Setting channels automatically
— Auto Channel Set

Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.

A

Access Main Menu screen, then Tuner
Set screen

Press MENU on the Remote. Press

rt

to

move the highlight bar (arrow) to “TUNER
SET”, then press OK or

e

.

B

Perform Auto Channel Set

Press

rt

to move the highlight bar

(arrow) to “AUTO CHANNEL SET”, then
press OK or

e

. The VCR selects the correct

band (TV or CATV) automatically during
Auto Channel Set.

● When Auto Channel Set is complete,

“SCAN COMPLETED” appears on
screen.

● If the scan was unsuccessful, “SCAN

COMPLETED–NO SIGNAL–” appears on
screen. Check the connections and start
again.

Press MENU to return to normal screen.

Setting channels manually
— Manual Channel Set

You can add the channels you want or delete the channels you do
not want manually.

A

Access Main Menu screen, then Tuner
Set screen

Press MENU on the Remote. Press

rt

to

move the highlight bar (arrow) to “TUNER
SET”, then press OK or

e

.

B

Access Manual Channel Set screen

Press

rt

to move the highlight bar

(arrow) to “MANUAL CHANNEL SET”,
then press OK or

e

.

C

Add or skip desired channels

To add channels

A

Press the Number keys on the Remote
to input a channel number you want to
add.

B

Press OK or

e

to set to “ADD”.

C

Repeat

A to B to add other channels.

Press MENU to return to normal screen.

To skip channels

A

Press

rt

or the Number keys to select a channel number you

want to skip.

B

Press OK or

e

to set to “SKIP”.

C

Repeat

A and B to skip other channels. Press MENU to return

to normal screen.

Cable Box and/or DBS Receiver Control
Setting

The following procedure is required if you receive your TV
channels through a cable box (descrambler) and/or if you receive
satellite channels through DBS (Direct Broadcast Satellite)
receiver. The Controller allows the VCR to automatically switch
the cable box or DBS receiver’s channel during timer recording.

NOTES:

● The Controller is not supplied with this unit. It can be requested

by mailing in the completed JVC Cable Mouse Certificate that is
included with the accessory package.

● For the cable box, the Controller is effective for VCR Plus+ or

Express timer programing.

● For the DBS receiver, the Controller is effective only for Express

timer programing.

● When connecting your cable box or DBS receiver, refer to its

instruction manual.

A

Situate Controller

If both a cable box and a DBS receiver are used, position the
Controller so its signal reaches the remote sensors on both the
cable box and DBS receiver.

B

Attach Controller

Fix securely using the adhesive strip attached on the back of the
Controller.

C

Connect cable box and/or DBS receiver to VCR

● If your cable box or DBS receiver does not have audio/video

output connectors, connect the RF output terminal on the unit to
the ANT. IN terminal on the rear of your VCR.

● If your cable box or DBS receiver has audio/video output

connectors, connect an audio/video cable between the AUDIO/
VIDEO IN connectors on the rear of the VCR and the audio/
video output connectors on the unit.

● If both a cable box and a DBS receiver are used, it is

recommended that you connect the DBS receiver to your VCR’s
AUDIO/VIDEO IN connectors and the cable box to your VCR’s
ANT. IN connector.

After a power failure occurs...

● Band selection will be reset to “CATV”.

Your VCR

Cable box or DBS receiver

Controller
(suggested locations)

Transmitter

Controller

Cable box or DBS receiver

To ANT. IN

To AUDIO/VIDEO IN

RF out

Audio/video output

VCR

CONTINUED ON NEXT PAGE

Advertising