Ex500 mono sub with powered satellites, Operating the ex500, Left – Samson EX500 User Manual
Page 10
8
Operating the EX500
30
105
200
Hz
0
5
10
P O W E R E D S U B W O O F E R 5 0 0 WAT T S
EX500
SAMSON
POWER
ON
OFF
A.C. MAINS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
POWER
RATING
115V/230V 50HZ/60Hz 500W
AVIS;
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
SERIAL
No.
60Hz
50Hz
230VAC
MADE IN CHINA
LEVEL
MONO
PEAK
SWEEP
RIGHT
LEFT
RIGHT
LEFT
BALANCED INPUTS
BALANCED HIGH PASS OUTPUTS
STEREO
E N G I N E E R E D A N D D E S I G N E D
I N T H E U N I T E D S TAT E S
B Y S A M S O N T E C H N O L O G I E S
•
•
•
•
•
•
•
•
•
•
•
•
115VAC
MONO
STEREO
!
0
10
5
!
0
10
5
PL 1602 16 CHANNEL LINE MIXER
SAMSON TECHNOLOGIES CORP., NEW YORK, U.S.A.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
120V - 60 Hz 35W
POWER
RATING
AVIS:
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE
ON
OFF
MIC 3
MAIN OUT
BALANCED 600 +4db
TIP + RING - SLEEVE GND
AUX
RETURNS
UNBALANCED 10K‰
1L
AUX SEND
UNBALANCED
2K‰ +4db
2R
1L
2R
3L
4R
5L
6R
7L
8R
9L
10R
11L
12R
13L
14R
15L
16R
INPUTS BALANCED 10K‰ -30 to +4db TIP + RING - SLEEVE GND.
6R
5L
4R
3L
2R
1L
INSERTS TIP RETURN RING SEND
1
2
3
1
2
3
-40
+4
0
-10
TRIM
-40
+4
0
-10
TRIM
1L
2R
3L
4R
L
R
L
R
BUS
INSERTS
MIXER LINKING
110
POWER
S / N
~115V(0.3A)
230V(0.15A)
50/60Hz 30W
MIC 1
PL1602 Mixer
EX500
EX20
EX20
The EX500 is a perfect addition to any pair of powered full range enclosures like the Samson EX20 and EX30.
Below is a typical system set-up using the EX500 with a mixer and a pair of powered satellite loudspeakers. The
EX500’s input and outputs utilize industry standard XLR connectors. For a detailed wiring diagram, see the sec-
tion EX500 Connections on page 12. Follow the steps below the diagram to set up your system.
EX500 MONO SUB WITH POWERED SATELLITES
•
Connect the mixer’s left output to the EX500’s left
input and the mixer’s right output to the EX500’s right
input. Now connect the EX500’s left output to the
input of the left side powered satellite, and the
EX500’s right output to the input of the right side
satellite. Switch the Stereo/Mono selector switch to
the MONO position.
•
Now adjust the crossover SWEEP to the desired fre-
quency. For the Expedition EX20 & EX30 select 80-
100Hz. If you are using another brand of powered
speaker as satellites with the EX500, consult their
respective owners manuals for the recommended
crossover point.
•
Lower your mixer’s master outputs to all the way off.
Now set the level of your powered satellites up to the
normal operating level. Run an audio signal (like
some music from a CD) through your mixer and raise
the level to a comfortable listening volume. Now
slowly raise the EX500 Level control and listen to the
low frequency output. Adjust the EX500 to the level
of low frequency output that you like. Now, when
you raise and lower your mixer’s output, the EX500
and satellites will track at the same relative volume.
30
105
200
Hz
0
5
10
P O W E R E D S U B W O
LEVEL
MONO
PEAK
SWEEP
LEFT
BALA
STEREO
•
•
•
•
•
•
•
•
•
•
•
•