Samson Power Amplifiers User Manual

Page 17

Advertising

OUTPUT

XLR and 1/4" jack

Key Input Connector

1/4" jack

Key Output Connector

1/4" jack

Dimensions

1.5/8" (h) x 8.5/8" (w) 7 1/4" (d)

41.5 mm (h) x 215 mm (w) x 184 mm (d)

Net Weight

5.5lbs., (2.5 kg)

Shipping Weight

8lbs., (3.6 kg)

S•Direct

Direct Box

Frequency Response

5-35 kHz, -3 dB

Noise Level (22-22kHz, Input Shorted)

-104 dBu

THD + N (10 Hz -22 kHz)

0.013% typ. @ 1 VRMS,1 kHz.

Input Impedance

(GTR) 1 Meg. Ohm

(SPK) 10 k Ohm

Max. Input Level (1% THD)

+8.1 dBu ( 9v. Batt.)

+11.3 dBu (48v. Phantom)

GTR/SPK Input

1/4

″

Phone Jack, unbalanced

OUTPUT/LINK

1/4

″

Phone Jack, unbalanced

BALANCED OUTPUT

XLR Connector, balanced

Phantom Power

24-48 VDC

Battery

9 Volt

Dimensions

″

(h) x 5.6

″

(w) x 4

″

(d)

50.8mm (h) 142mm (w) x 101.6mm (d)

Weight

15 oz. • .43 Kg

S•Monitor

Personal Monitor

Specifications TBD

S•Mix

5-channel Mixer

Specifications TBD

S•Amp

4-channel Headphone Amp

Specifications TBD

S•Convert

+4 to -10dB/-10 to +4dB Converter

Specifications TBD

Mixers

MDR6
Frequency Response
Mic to Main

5 Hz - 54 kHz

Line to Main

5 Hz - 54 kHz

Aux Return to Main

5 Hz - 98 kHz

Line to Aux Send

5 Hz - 57 kHz

T.H.D.

0.02%

Residual Noise (30 kHz LPF, all control Min)
Main

-89 dBu

Aux Send

-86 dBu

Crosstalk (@ 1 kHz w/ 30 kHz LPF)
Ch vs. Ch

75 dB

Input vs. Output

87.5 dB

Peak LED Sensitivity (before clipping)

5 dB

CLIP Indicators

Turn on: THD> 0.1%

Headphone output (600 ohm load)

100 mW

Maximum Input Level (1 kHz, ± 3dB)
Mic Input (Mono Ch)

10.5 dBu

Line Input (Stereo Ch)

7.6 dBu

Input Channel Equalizer (± 2dB)
High (shelving)

12 kHz ±15 dB

Mid (peaking)

2.5 kHz ± 15 dB

Low (shelving)

80 Hz ±15 dB

Meters 6 point LED meter (-20, -12, -6, 0, +6dB and PEAK)
Phantom Power

+48V

Power Consumption

300W 1/8 power, 540W full

Dimensions (W x D x H)

2.7

≤

(h) x 6.4

≤

(w) x 9

≤

(d)

69 mm (h) x 163 mm (d) x 228 mm (w)

Weight

4.5 lbs • 2.04 Kg

MDR8
Frequency Response (Trim @ Min, unity gain ± 3 dB)
Mic to Main

5 Hz - 54 kHz

Line to Main

5 Hz - 54 kHz

Aux Return to Main

5 Hz - 98 kHz

Line to Aux Send

5 Hz - 57 kHz

T.H.D.

0.02%

Residual Noise (30 kHz LPF, all control Min)
Main

-89 dBu

Aux Send

-86 dBu

Crosstalk (@ 1 kHz w/ 30 kHz LPF)
Ch vs. Ch

75 dB

Input vs. Output

87.5 dB

Peak LED Sensitivity (before clipping)

5 dB

CLIP Indicators

Turn on: THD> 0.1%

Headphone output (600 ohm load)

100 mW

Maximum Input Level

(1 kHz, ± 3dB)

Mic Input (Mono Ch)

10.5 dBu

Line Input (Stereo Ch)

7.6 dBu

Input Channel Equalizer

(± 2dB)

High (shelving)

12 kHz ±15 dB

Mid (peaking)

2.5 kHz ± 15 dB

Low (shelving)

80 Hz ±15 dB

Meters

6 POINT LED METERS (-20, -12, -6, 0, +6dB and

PEAK)

Internal DSP Effects

24 BIT -8 presets: 1 - Large Hall; 2 Medium Hall,

3 - Large Room; 4 - Vocal Room 1; 5 - Vocal

Room 2; 6 - Chorus + Reverb; 7 - Chorus +

Delay; 8 - Stairwell

Phantom Power

+48V

Power Consumption

300W 1/8 power, 540W full

Dimensions (W x D x H)

3 1/2

≤

(h) x 11 1/2

≤

(w) x 11 3/4

≤

(d)

89 mm (h) x 292mm (w) x 299mm (d)

Weight

6.5 lbs. • (3 Kg)

MDR 10
Specifications TBD

MDR 16
Specifications TBD

Mixpad 4
Mic EIN:

-128 dBu

Line EIN:

-111 dBu

Frequency response:

10 Hz to 54 kHz

Total harmonic distortion (with 30 kHz LPF):

.004%

EQUALIZATION

High (12 kHz):

±15 dB

Mid (2.5 kHz):

±12 dB

Low (80 Hz):

±15 dB

Battery operation:

Three 9V alkaline

Dimensions:

2.7

″

(h) x 6.4

″

(w) x 9

″

(d)

69 mm x (h) 163 mm (w) x 228 mm (d)

Weight:

1.85 lbs. • .839 kg.

Powered Mixers

TM300
MIXER/PREAMP SECTION
Frequency response (± 1 dB):

<20 Hz to 20 kHz

Total harmonic distortion:

< 0.02%

Graphic Equalizer:

7 band ±12 dB

Phantom power

+48 V

POWER AMP SECTION
Maximum output power (1 kHz):

150 W per channel into 4

Ω

Total harmonic distortion:

< 0.2%

Signal-to-noise ratio:

>100 dB

Frequency response (± 3 dB):

<12 Hz to 20 kHz

GENERAL
Power consumption:

780 w

Power requirements:

115 Vac • 50/60 Hz

230 Vac • 50 Hz

Dimensions:

5.5

″

(h) x 19.35

″

(w) x 13.75

″

(d)

139 mm (h) x 349 mm (w) x 491 mm (d)

Weight:

29.7 lbs. • 13.5 kg

TM500
MIXER/PREAMP SECTION
Frequency response (± 1 dB):

<20 Hz to 20 kHz

Total harmonic distortion:

< 0.02%

Graphic Equalizer:

7 band ±12 dB

Phantom power

+48 V

POWER AMP SECTION
Maximum output power (1 kHz):

250 W per channel into 4

Ω

Total harmonic distortion:

< 0.2%

Signal-to-noise ratio:

>100 dB

Frequency response (± 3 dB):

<12 Hz to 20 kHz

GENERAL
Power consumption:

1100 w

Power requirements:

115 Vac • 50/60 Hz

230 Vac • 50 Hz

Dimensions:

5.5

″

(h) x 19.35

″

(w) x 13.75

″

(d)

139 mm (h) x 349 mm (w) x 491 mm (d)

Weight:

36 lbs. • 16.4 kg

PA324
Rated Output power

150W/4

Ω

@0.5% THD at 1KHz per amplifier

Frequency response

20Hz~20KHz±0.5dB@1W Output into 8

Ω

(AMP

OUT)

20 Hz~20KHz ±0.5@+4dB Output into 10

Ω

(MAIN OUT, MONITOR OUT, EFX SEND)

Total Harmonic Distortion

< 0.1%@20Hz~20KHz, 75W output into4

Ω

(AMP OUT)

Less than 0.1%@20 Hz~20KHz+14dB output into

10K

Ω

(MAIN OUT, MON OUT, EFX SEND)

Hum & Noise

-121dB equivalent input noise

(Average, RS+150

Ω

)

-100dB residual output noise (MAIN OUT, MONI-

TOR OUT, EFX OUT)

(with 20Hz~20KHz BPF)

-79dB (MAIN OUT, MONITOR OUT) Master level

control at maximum all channel level control at

minimum.

-79dB (EFX OUT) Master level control at maxi

mum all channel level controls at minimum

Crosstalk 1KHz

70dB adjacent input, 70dB input to output

Input Channel Equalization

HIGH

12KHz shelving (± 15dB Maximum)

MID

2.5KHz peaking (± 12dB Maximum)

LOW

80Hz shelving (± 15dB Maximum)

Meters

7 POINT LED METERS (-20, -10, -7, -4, 0, +3, +6dB)

Graphic Equalizer

7 bands (63, 160, 400, 1K, 2.5K, 6.4K, 16KHz)

Internal DSP Effects

24 BIT - 8

Dimensions

19.25

″

(w) x 11.25

″

(h x 11.4

″ (

489mm (w) x 286mm (h) x 289mm (d)

Weight

32.3 lbs.•14.7Kg

Power Distribution & Rack Gear

S Patch Plus

48 Channel, fully Balanced patchbay

Channel

Switchable configuration modes

Normal, Half-normal and Thru

Dimensions

1 3/4

″

(h) x 19

″

(w) x 3

″

(d)

44.45 mm (h) x 482.6 mm (w) x 76.2 (d)

Weight

3.8 lbs. • (1.72 Kg)

PowerBrite Pro7/Pro9
Number of Outlets

Pro7:

6 switched, 1 unswitched

Pro9:

8 switched, 1 unswitched

Max. Current:

Pro7 15 Amps/Pro9 10 Amps

Input Voltage (RMS):

Pro7 130 Vac/Pro9 245 Vac

Spike Protection Mode:

Hot to Neutral, Hot to Ground,

and Neutral to Ground

Max. Clamping Voltage (@ 50 A):

700 Vac

Response Time:

1 nanosecond

Max. Surge Current:

4,500 Amps (8 x 20 ms pulse)

Max. Spike Energy:

104 Joules

Noise Attenuation:

> 20 dB, 1.5 MHz to 200 MHz

AC Inlet:

PS9 North America/PS11 IEC

Lamp/Starter:

Fluorescent F45CW condenser type FS2

Lamp Life:

3000 hours 95 Lumens

Starter Fuse (Internal):

500 ma T type

Dimensions:

1.75

″

(h) x 19

″

(w) x 7.5

″

(d)

44 (h) x 482 mm (w) x 190 (d)

Weight:

7 lbs. • 3.2 kg

Conforms:

UL/CUL/CE/LVD

PowerBrite PB9/PB11
Number of Outlets

PB9:

8 switched, 1 unswitched

PB11:

10 switched, 1 unswitched

Max. Current:

PB9 15 Amps/PB11 10 Amps

Input Voltage (RMS):

PB9 130 Vac/PB11 245 Vac

Spike Protection Mode:

Hot to Neutral, Hot to Ground,

and Neutral to Ground

Max. Clamping Voltage (@ 50 A):

700 Vac

Response Time:

1 nanosecond

Max. Surge Current:

4,500 Amps (8 x 20 ms pulse)

Max. Spike Energy:

104 Joules

Noise Attenuation:

> 20 dB, 1.5 MHz to 200 MHz

AC Inlet:

PS9 North America/PS11 IEC

Lamp/Starter:

Fluorescent F45CW condenser type FS2

Lamp Life:

3000 hours 95 Lumens

Starter Fuse (Internal):

500 ma T type

Dimensions:

1.75

″

(h) x 19

″

(w) x 7.5

″

(d)

44 (h) x 482 mm (w) x 190 (d)

Weight:

7 lbs. • 3.2 kg

Conforms:

UL/CUL/CE/LVD

PowerStrip PS9/PS11
Number of Outlets

PS9:

8 switched, 1 unswitched

PS11:

10 switched, 1 unswitched

Max. Current:

PS9 15 Amps/PS11 10 Amps

Input Voltage (RMS):

PS9 130 Vac/PS11 245 Vac

Spike Protection Mode:

Hot to Neutral, Hot to Ground,

and Neutral to Ground

Max. Clamping Voltage (@ 50 A):

700 Vac

Response Time:

1 nanosecond

Max. Surge Current:

4,500 Amps (8 x 20 ms pulse)

Max. Spike Energy:

104 Joules

Noise Attenuation:

> 20 dB, 1.5 MHz to 200 MHz

AC Inlet:

PS9 North America/PS11 IEC

Dimensions:

1.75

″

(h) x 19

″

(w) x 7.5

″

(d)

44 (h) x 482 mm (w) x 190 (d)

Weight:

7 lbs. • 3.2 kg

Conforms:

UL/CUL/CE/LVD

Audio Equipment

Resolv 50a

Rated Output Power

Low frequency amp:

50 watts @1K into 4ohms

High frequency amp:

25 watts @ 10K into 4ohms

Frequency Response:

Low amp:

tbd

High amp:

tbd

Distortion THD:

tbd

Power consumption:

75 watts

Frequency response:

tbd

Driver:

5.25" Woofer Shielded

Tweeter:

″

Dome Shielded

Dimensions:

tbd

Weight:

tbd

Resolv 65a
Rated Output Power

Low frequency amp:

75 watts @1K into 4ohms

High frequency amp:

30 watts @ 10K into 4ohms

Frequency Response:

Low amp:

40hz-3200

High amp:

3200-50K

Distortion THD:

<.05%

Power consumption:

150 watts

Frequency response:

40 Hz to 20 kHz

Driver:

6 1/2" Woofer Shielded

Tweeter:

″

Dome Shielded

Dimensions:

13 5/8"(H) x 8 1/2" (W) x 9 7/8" (D)

Weight:

18 lbs. • 8.2 kg

Resolv 65
Power Rating:

75 watts

Impedance:

8 ohm

Frequency response:

40 Hz to 20 kHz

Driver:

6 1/2

″

Woofer Shielded

Tweeter:

″

Dome Shielded

Dimensions:

13 5/8"(H) x 8 1/2" (W) x 9 7/8" (D)

Weight:

13.4 lbs. • 6.1 kg

Resolv 80a
Rated Output Power

Low frequency amp:

75 watts @1K into 4ohms

High frequency amp:

25 watts @ 10K into 4ohms

Frequency Response:

Low amp:

tbd

High amp:

tbd

Distortion THD:

tbd

Power consumption:

100 watts

Frequency response:

tbd

Driver:

8" Woofer Shielded

Tweeter:

″

Dome Shielded

Resolv Sub 120
Amp:

120watts into 4ohms

Frequency Response:

30hz-150

Distortion THD:

<.05%

Power consumption:

210 watts

Driver:

″

long stroke

Dimensions:

14 1/2

″

(H) x 14 1/2

″

(W) x 17.5

″

(D)

Weight:

39 lbs. • 17.75 kg

Expedition Express
Power Rating: (@ 8

Ω

250 Watts Program

Frequency Response:

60 Hz – 15 kHz ± 3 dB

Sensitivity:

97 dB SPL @ 1W/1m

Crossover Frequency:

2.3 kHz (12 dB Per Octave)

LF Driver:

≤

heavy-duty driver ,

2.5

≤

voice coil (Kapton Former),

50 oz. barium ferrite magnet

HF Driver: 1

≤

titanium compression driver

Stereo Mixer Section:
Inputs

2 Mic/Line XLR/TRS,

1 Stereo Line w/Mic XLR

Frequency Response

10 Hz - 50 kHz

Crosstalk

70 dB @ 1 kHz

Equalization Frequencies

100 Hz (Low), 10 kHz (High)

Effects

DSP Reverb with 6 Presets

Mounting:

Integral 1 3/8

≤

Pole Mount Receptacle, Fly Points

Dimensions: EX250m and EX250e

21 1/4 (h) x 14 5/8 in. (w) x 17 3/8 (d)

539 mm (h) x 371 mm (w) x 441 (d)

Weight:
EX250e

28.5 lbs • 12.9 kg

EX250m

45.0 lbs • 20.4 kg

XP100
Power Rating:

250 Watts Program; 400 Watts Max. Peak

Frequency Response

60 Hz – 15 kHz

Sensitivity

97 dB SPL @ 1W/1m

Crossover Frequency

2.3 kHz (24 dB Per Octave)

LF Driver

″

heavy-duty driver

2.5

″

voice coil (Kapton Former)

Advertising

Popular Brands

Popular manuals