Samson SERVO 200 - Manual (Page 2)

ARCHITECT’S & ENGINEER’S SPECIFICATIONS
The Samson Servo 200 shall be a two space, rackmount
stereo power amplifier. It shall deliver 100 watts per channel
at 4 Ohms or 200 watts into 8 Ohms in bridge mono mode.
It shall have 1/4 inch balanced inputs and RCA unbalanced
inputs. It shall be a bi-polar design and use a toroidal
transformer. The front panel shall have volume controls and
LED metering for each channel. The rear panel shall also
have 5 way binding posts for the amplifier outputs.
SERVO 200 SPECIFICATIONS
Stereo both channel driven
8 Ohms .............................. 66 Watts x 2
4 Ohms .............................. 100 Watts x 2
Bridged mono
8 Ohms .............................. 200 Watts
Signal to Noise Ratio (20Hz-20k) ...... 102dB
Distortion (SMPTE-IM) ..................... 0.05%
Input sensitivity @8 Ohms ................ 1.24V(4dBu)
Voltage Gain .................................... 32dB
Output Circuitry Class ....................... AB
AC Power
@1/8 rated power 4 Ohms, max. ....... 0.4A
@1/3 rated power 4 Ohms, max. ....... 1.1A
@ rated power 4 Ohms, max. ............ 3.3A
Distortion (typical @4 Ohms)
20Hz-20kHz, 10dB below
rated power ..................................... 0.01%
1kHz, rated power ........................... 0.1%
Frequency Response
@8 Ohms, 1 Watt, 20Hz-20kHz ........ 20Hz-20kHz
Damping Factor (400Hz) ................... 280
Input Impedance .............................. 15 kOhm Unbalanced,
30 kOhm B alanced
Input Clipping .................................. 10 Vrms (22dBu)
Cooling ........................................... Continuously variable speed,
fan forced air
Connectors (each channel)
Input ................................. RCA unbalanced and 1/4˝
(6.3mm) TRS, balanced
Output ............................... 5-way Binding post and
1/4˝ Phone
Controls .......................................... AC power switch,Channel 1
and 2 volume
Indicators ....................................... Power on (blue), Protection
(amber), Signal (green) for
each Ch., Peak(red) for each
Ch. Level: -24 dB, -20 dB,
-16 dB, -12 dB, -8 dB, -4 dB,
-2 dB. O, +2 dB and +4 dB
(PEAK).
Protection ....................................... Short circuit,Thermal,Current
limit,DC offset,Current inrush,
RF protection, Turn on/Turn
off muting
Power Requirements ......................... 115/230, 240VAC, 50/60Hz
Dimensions (W x H x D) .................... 19 ˝ x 3.5˝ x 11.7˝
(483mm x 89mm x 297mm)
Net Weight ...................................... 15 lbs (6.82 kg)
SERVO 200
PRODUCT SPECIFICATION SHEET
SERIES DESCRIPTION CATEGORY
SERVO 200 POWER AMPLIFIER AMPLIFIERS
FEATURES
(continued)
> Unique stable bipolar circuit design that continuously
keeps DC output during idling at or near zero volts (thus
keeping idle speakers at their zero point). This serves to
minimize heat overload problems by effectively preventing
the Servo 200 from applying power when unnecessary.
> Forced air cooling via two temperature-sensitive, variable
speed fans provides reliable performance without thermal
and overheating problems.
> Protection relay circuitry (with dedicated LEDs for each
channel) that guards against overheating or faulty wiring
conditions and also prevents “thumps” when powering on or
off. This means that you can use the Servo 200 with a single
power strip into which a mixer or other audio devices are
connected, without danger of damage to connected speakers.
> Input connectors for each channel accommodate both RCA
or balanced 1/4-inch TRS plugs.
> Output connections are made via 5-way binding posts.
> Toroidal transformer power supply for high current and low profile.
> The Servo 200 can be mounted in any standard 19˝ rack
(taking just two rack spaces), making it easy to integrate
the amp into any fixed or traveling PA rig.
> Rugged construction (an all-steel chassis with a cool gray
finish and a lightweight anodized aluminum heat sink)
makes the Servo 200 eminently roadworthy.
> Extended three-year warranty.
437.5 mm
483 mm
88 mm
297mm
POWER