Skylink WE-001 - Manual (Page 2)

5. ON / OFF OPERATION
Use a Transmitter
When the programmed button of a transmitter is activated, it will transmit
a signal to toggle the status of the load. For example, if a toggle signal is
received when the light is off, that signal will turn on the light.
6. COUNTDOWN TIMER OPERATING MODE
Use the Wall Switch
To turn on / off the load, simply push the button of the wall switch once,
it will toggle the status of the
light, i.e. from on to off or from off to on.
Note: Once the number of flashes reaches 5, it will stay at this setting. If
you would like to go back to other settings, such as 1 minute, release the
button and repeat from step 1 to start over.
Once a transmitter (button) is programmed for timer mode, activating this
programmed transmitter (button) will turn on the load for the specified timer
duration.
During a timer count down, if the Wall Switch receives another signal for
timer operation, the timer will start again and overrides the previous timer,
therefore, extending the On period by another timer interval.
To stop timer count down, press a programmed button for On/Off mode,
or press the switch button on the Wall Switch.
4. SET TIMER DURATION (CONT)
Input Voltage: 120V AC, 60Hz
Maximum Ballast Load: 500W
Maximum Tungsten Load: 600W
Maximum Resistive Load: 1000W
Operating Frequency: 318MHz
Range: Up to 500 feet in open area
Standby Current: 0.2mA
Minimum Load: 10W
o o Operational Temperature: -4 F - 140 F o o (-20 C - 60 C)
Humidity: 5%-95%
8. TECHNICAL SPECIFICATIONS
9. FCC
The device is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
11. CUSTOMER SERVICE
7. ERASING TRANSMITTERS FROM WALL SWITCH
12. ACCESSORIES
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z844-003 R3
Patent Pending
©2010 SKYLINK GROUP
The Skylink System consists of many other devices such as
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
TM Home
TM
TM
10. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
Refer to the user's instructions of the transmitter for more detailed
instructions for dimming operation, as well as other operations such as
Zone On / Zone Off, All On / All Off etc.
Note: If the 2 blue LEDs are off when the loading is off, please check
and ensure the light bulb is installed and in good condition.
If a Countdown Timer Mode transmitter or sensor is activated, the light
connected to the Wall Switch will be on for the predetermined time interval.
During the timer count down, the upper blue LED on the Wall Switch will
be on steadily, the lower blue LED will start to flash during the last minute
of the countdown timer. Activating a programmed transmitter or sensor
under Regular Mode during timer interval can override the countdown
timer operation.
1. Push the Switch Button on the Wall Switch. The connected load will be
on, and the 2 blue LEDs are off.
2. Transmit a "Erase" code from the transmitter until step 5. Refer to the
user's instructions of the transmitter on how to transmit a "Erase" code.
3. Press and hold the "SET" button on the Wall Switch about 3 seconds,
until the upper blue LED flashes.
4. Release the "SET" button.
5. You may stop the "Erase" code signal transmission. You have
successfully erased all the devices from the Wall Switch.