Sony 500WSPL - Manual (Page 88)

88
Chapter 4 Viewfinder Screen Indications and Menus
Chapter 4 Viewfinder Screen Indications and Menus
Viewfinder Advanced Menu
Advanced menu page 3
a) For DSR-500WSPL: EBU75
Item Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
LOW
Sets the L position. –3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB,
12 dB, 18 dB, 18 dB + DPR,
24 dB
MID
Sets the M position. 0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB,
18 dB, 18 dB + DPR, 24 dB,
24 dB + DPR
HIGH
Sets the H position. 3 dB, 6 dB, 9 dB, 12 dB,
18 dB (normal value),
18 dB + DPR, 24 dB, 24 dB
+ DPR, HYPER GAIN
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to CAM/DL. ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in the basic menu page 2
(see page 81). For details on
the DynaLatitude function,
see page 50.
Advanced menu page 2
Item
AWB MEM
Selects whether or not
to make the FILTER
control settings (1 to 4)
correspond to
separate white
balance adjustment
values stored in
memory. 2 (normal value): No
correspondence with FILTER
control settings. Only two
adjustment values (A and B) are
stored in memory.
2
×
4FL: Correspondence with
FILTER control settings. Each of
the four control settings can be
used to set A and B adjustment
values, for a total of eight settings.
TONE
Selects whether or not
to output a 1-kHz
audio signal with the
color bars when the
OUTPUT/DL/DCC+
has been set to
BARS. ON (normal value): Outputs
audio signal.
OFF: Does not output audio
signal.
BARS
Selects normal width
or narrower width for
color bars. SMPTE (normal value for DSR-
500WSL): Normal width
EBU75 (normal value for DSR-
500WSPL): EBU 75%
EBU100 (for DSR-500WSPL):
EBU 100%
SPLIT (for DSR-500WSPL): Not
for normal operation
SNG: Narrower than normal (used
for satellite communications, etc.)
REMOTE1
Sets a function for
switch 1 of the RM-
LG1 connected to the
REMOTE connector 1. REC (normal value): Specifies
recording start/stop.
MARK: Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2
Sets a function for
switch 2 of the RM-
LG1 connected to the
REMOTE connector 1.
9600, 38400 (normal value)
REC: Specifies recording start/stop.
MARK (normal value): Specifies
a Mark IN/OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
Settings
BAUD RATE
Sets a baud rate for a
computer connected
to the REMOTE
connector 2 (to be
supported in the future
version).
P A G E 2 ( N E X T m $ P R E V m4)
G A I N
m L O W : O d B
M I D : 9 d B
H I G H : 1 8 d B
H Y P E R : 3 6 d B
D L : O N
E X I T M E N U ( Y E S m P U S H )
P A G E 3 ( N E X T m $ P R E V m4)
m A W B M E M : 2
T O N E : O N
B A R S : S M P T E
R E M O T E 1 : R E C
R E M O T E 2 : M A R K
B A U D R A T E : 3 8 4 0 0
E X I T M E N U ( Y E S m P U S H )
a)
HYPER
Sets the HYPER position. 36 dB (normal value),
42 dB