Seagate Cheetah 15K.5 FC ST373455FC User Manual
Cheetah 15k.5 fc
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- 1.0 Scope 1
- 2.0 Applicable standards and reference documentation 3
- 3.0 General description 7
- 4.0 Performance characteristics 11
- 5.0 Reliability specifications 15
- 6.0 Physical/electrical specifications 23
- 7.0 Defect and error management 39
- 8.0 Installation 43
- 9.0 Interface requirements 47
- 9.1 FC-AL features 47
- 9.1.1 Fibre Channel link service frames 47
- 9.1.2 Fibre Channel task management functions 48
- 9.1.3 Fibre Channel task management responses 48
- 9.1.4 Fibre Channel port login 49
- 9.1.5 Fibre Channel port login accept 50
- 9.1.6 Fibre Channel Process Login 50
- 9.1.7 Fibre Channel Process Login Accept 51
- 9.1.8 Fibre Channel fabric login 51
- 9.1.9 Fibre Channel fabric accept login 52
- 9.1.10 Fibre Channel Arbitrated Loop options 53
- 9.2 Dual port support 53
- 9.3 SCSI commands supported 54
- 9.4 Miscellaneous operating features and conditions 63
- 9.5 FC-AL physical interface 64
- 9.5.1 Physical characteristics 64
- 9.5.2 Connector requirements 65
- 9.5.3 Electrical description 65
- 9.5.4 Pin descriptions 65
- 9.5.5 FC-AL transmitters and receivers 66
- 9.5.6 Power 67
- 9.5.7 Fault LED Out 67
- 9.5.8 Active LED Out 68
- 9.5.9 Enable port bypass signals 68
- 9.5.10 Motor start controls 68
- 9.5.11 SEL_6 through SEL_0 ID lines 69
- 9.5.12 Device control codes 71
- 9.6 Signal characteristics 71
- 9.1 FC-AL features 47
- 10.0 Seagate Technology support services 75
- Figure 1. Typical ST3300655FC drive, 4 Gbit, +12V current profile 26
- Figure 2. Typical ST3300655FC drive, 4 Gbit, +5V current profile 26
- Figure 3. Typical ST3146855FC drive, 4 Gbit, +12V current profile 27
- Figure 4. Typical ST3146855FC drive, 4 Gbit, +5V current profile 27
- Figure 5. Typical ST373455FC drive, 4 Gbit, +12V current profile 28
- Figure 6. Typical ST373455FC drive. 4 Gbit, +5V current profile 28
- Figure 7. ST3300655FC DC current and power vs. input/output operations per second at 4 Gbit 29
- Figure 8. ST3146855FC DC current and power vs. input/output operations per second at 4 Gbit 30
- Figure 9. ST373455FC DC current and power vs. input/output operations per second at 4 Gbit 31
- Figure 10. Locations of the HDA temperature check point 32
- Figure 11. Recommended mounting 34
- Figure 12. Mounting configuration dimensions 37
- Figure 13. Air flow 44
- Figure 14. Physical interface 64
- Figure 15. Port bypass circuit physical interconnect 64
- Figure 16. FC-AL SCA device connector dimensions 65
- Figure 17. FC-AL transmitters and receivers 66
- Figure 18. Transmit eye diagram 72
- Figure 19. Receive eye diagram 73
- 1.0 Scope
- 2.0 Applicable standards and reference documentation
- 3.0 General description
- 4.0 Performance characteristics
- 5.0 Reliability specifications
- 6.0 Physical/electrical specifications
- 7.0 Defect and error management
- 8.0 Installation
- 9.0 Interface requirements
- 9.1 FC-AL features
- 9.1.1 Fibre Channel link service frames
- 9.1.2 Fibre Channel task management functions
- 9.1.3 Fibre Channel task management responses
- 9.1.4 Fibre Channel port login
- 9.1.5 Fibre Channel port login accept
- 9.1.6 Fibre Channel Process Login
- 9.1.7 Fibre Channel Process Login Accept
- 9.1.8 Fibre Channel fabric login
- 9.1.9 Fibre Channel fabric accept login
- 9.1.10 Fibre Channel Arbitrated Loop options
- 9.2 Dual port support
- 9.3 SCSI commands supported
- 9.4 Miscellaneous operating features and conditions
- 9.5 FC-AL physical interface
- 9.5.1 Physical characteristics
- 9.5.2 Connector requirements
- 9.5.3 Electrical description
- 9.5.4 Pin descriptions
- 9.5.5 FC-AL transmitters and receivers
- 9.5.6 Power
- 9.5.7 Fault LED Out
- 9.5.8 Active LED Out
- 9.5.9 Enable port bypass signals
- 9.5.10 Motor start controls
- 9.5.11 SEL_6 through SEL_0 ID lines
- 9.5.12 Device control codes
- 9.6 Signal characteristics
- 9.1 FC-AL features
- 10.0 Seagate Technology support services