Sharp CDPC3500 User Manual
Page 15
<P=005>
(Continued)
■
Disc number selection
1
When stopped, press the DISC SKIP button.
2
Press the
0/R
(
0R
) button.
●
The next disc playback will begin, after which each following
disc will be played sequentially.
Notes:
●
When the DISC SKIP button is pressed during playback,
playback will begin automatically from the next disc.
(It is not necessary to press the
0/R
(
0R
) button.)
●
When one of the disc number buttons ( 1- 3) is pressed
during playback, playback of the selected disc will begin auto-
matically. (It is not necessary to press the
0/R
(
0R
) button.)
■
APSS (Auto Program Search System)
APSS automatically locates the beginning of any track.
To listen again to the track being played:
Press the
5
button for less than 0.5 seconds during playback.
To move to the beginning of the next track:
Press the
4
button for less than 0.5 seconds during playback.
●
To skip a number of tracks at one time, press the
5
or
4
button repeatedly until the desired track number is shown.
●
To start playing at a desired track, press the
5
or
4
button
while in the stop mode to select the track number, and then
press the
0/R
(
0R
) button.
Note:
●
APSS can only search for music on a single disc.
■
Cue and review
1
Load a disc and begin playback.
2
Hold down the
2
button for audible fast forward, and hold
down the
3
button for audible fast reverse.
3
Normal playback will resume when the
3
or
2
button is
released.
Notes:
●
When the end of the disc is reached while cueing, "END" will
appear in the display and CD operation will be paused. (Even
though the next disc has been loaded, the disc will not be
switched.)
Press the
3
button for fast reverse or press the
■
(CD
■
)
button to stop CD operation.
●
If the beginning of the disc is reached while reviewing, the
mode will automatically switch to normal playback at that point.
■
Random play
(Remote control operation)
The tracks on the disc(s) can be played in random order auto-
matically.
1
Load a disc(s) and close the disc tray.
2
Press the RANDOM button to begin random play.
●
"R" will appear.
Notes:
●
When using random play, be sure to press the
■
(CD
■
) button
after you are through listening.
Otherwise, the disc(s) will play continuously.
●
In random play the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
To cancel random play:
Press the
0/R
(
0R
) button.
●
"R" will go out.
CD
DISC SKIP
RANDOM
DISC SKIP
Caution:
●
Do not carry the unit with discs left in the disc
trays. The discs may come loose inside the
unit and they may be damaged or cause
damage to the unit. This may also cause mal-
functions.
●
Do not place two CDs in one disc position.
●
Do not push the disc tray while it is moving.
●
Do not attempt to turn the disc tray by hand. This
may cause malfunctions.
●
If the power fails while the tray is open, wait until
the power is restored.
●
If the disc tray is stopped forcibly, "ERR" will ap-
pear in the display and the unit will not function.
If this occurs, press the ON/STAND-BY button to
enter the stand-by mode and then turn the power
on again.
●
If TV or radio interference occurs during CD opera-
tion, move the unit away from the TV or radio.
●
If a disc is damaged, dirty, or loaded upside down,
the disc will be skipped and the next disc will auto-
matically play.
CD-PC3500(SEC) TINSE0281AWZZ
14