Document Outline

• Notices
• License
• Warnings and Cautions
  • AC Power
  • High Voltage
  • Robotics
  • Tapes
• 1 Introduction
  • About TreeFrog® Architecture
  • About This Guide
    • Related Publications
  • Getting Started
  • Conventions Used
  • How to Contact Spectra Logic Corporation
• 2 Installing the Library
  • Unpacking the Library
  • Attaching to the Host Computer
    • About the SCSI IDs and the SCSI Bus
    • LVD/SE or Differential SCSI Interface
    • LVD/SE SCSI Bus
    • Attaching the SCSI Cable
  • Attaching More than One SCSI Device
    • Verifying the SCSI Bus Requirements
    • Changing SCSI IDs as Necessary
  • Powering On the Library and Host Computer
    • Powering On the Library
    • Powering On the Host Computer
  • Inserting Media
  • Installing the Data Cartridge Magazine(s)
    • Reading and Writing Data to Tape
  • Using Horizontal and Rack Mounted Libraries
• 3 Configuring the Library
  • Changing the Library’s Configuration
    • About the Configuration Switch
    • Determine Your Configuration
  • Custom Configurations
    • Changing Configurations
    • Changing Configurations More than Once
• 4 Using the Library
  • Getting to Know the Library
    • Front Panel Components
    • Internal Components
    • Rear Panel Components
  • About AIT Bar Code Labels
  • Attaching Bar Code Labels
  • Using AIT Data Cartridges
    • Inserting and Removing Data Cartridges
    • Write-Protecting and Recording
    • Inserting a Tape Cartridge into a Drive
  • Using the Data Cartridge Magazine
    • Storing Cartridges Outside the Library
  • Getting Information from the Picker’s LED
  • Using the 30-Cartridge Library
• 5 Using the AIT Tape Drives
  • Getting to Know the AIT Tape Drive
    • Built-In Cleaning Feature
  • Getting Information From the Drive LEDs
  • Maintaining the AIT Tape Drive
    • Tape Drive Head Cleaning
    • Manual Drive Head Cleaning Operation
• 6 Library Stacker Mode
  • Stacker Mode Overview
    • Using Drive 1 Only
    • Thinking Like One Big Data Cartridge
  • Arranging Cartridges in the DCM
  • Controlling the Library Stacker
  • Using the Library in Stacker Mode
• 7 Maintenance, Troubleshooting, and Repairs
  • Maintaining the Library
    • Caring for Data Cartridges
    • Handling of Tape Cartridges
    • Caring for the Library
    • Replacing the Fuses
  • Updating Library Robotics Firmware
  • Troubleshooting the Library
    • Troubleshooting Library Initialization
    • Troubleshooting the Robotic Tape Picker
    • Troubleshooting SCSI Problems
    • Troubleshooting the Bar Code Reader
  • Purchasing Additional Library Accessories
  • Purchasing Bar Code Labels
  • Shipping Information
  • Spectra Logic Repair Policies
    • Notices
    • Limited Warranty
    • QuickSwap Service
    • Advanced Service Options
  • Contacting Spectra Logic
• Appendix A. Specifications
  • Library Storage Capacity
  • Sony AIT Tape Specifications
  • Sony AIT Tape Drive Specifications
  • Library Power Requirements
    • Fuses
  • Power Cable
    • 220-Volt AC Power Cord for Use in North America
    • 220-Volt AC Power Cord for International Use
  • Library Operating Environment Limits
  • Safety Agency Standards
• Appendix B. SCSI Cable and Terminator Requirements
  • SCSI Cable Requirements
  • SCSI Terminator Requirements
• Appendix C. Regulatory Notices
  • FCC Notice
  • Japan
  • Taiwan
  • EU Declaration of Conformity
• Index