Samsung DVD-V85 - Manual (Page 18)

34 35
GB GB
Using the G-CODE Feature ★(DVD-V80/DVD-V85 Only)
Timer Method
If you want to set
the timer program,
press the key.
G-Code
Code
Code : 0 - 9
Correct :
Standard
G-Code
Timer Method
OK
OPEN/CLOSE STANDBY/ON
7
1
★ (DVD-V70)
Recording a Programme with Automatic Stop
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1 Switch on the television.
2 To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3 Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
4 Select:
◆ The station to be recorded using the PROG ( or ) buttons
or
◆ The LINE1, LINE2 source using the INPUT SEL. button for a
satellite tuner or external video source
Result: The channel number is displayed and the programme
can be seen on the television.
5 Select the recording speed by pressing the SPEED button as
many times as required (see page 32).
6 Hold the REC button ( ● ) down for a while to start recording.
Result: The record indicator appears on the television screen
and DVD-VCR display. An index is recorded on the
tape (see page 42).
7 Press the REC button ( ● ) several times to increase the
recording time in:
◆ 30-minute intervals up to four hours
◆ 1-hour intervals up to nine hours
Result: The length is displayed on the television displays. The
selected programme is recorded for the length of time
requested. At the end of that time, the DVD-VCR stops
recording automatically and power off.
8 If you wish to cancel the recording before the end, press
STANDBY/ON.
☛
If the end of the tape is reached while recording:
◆ The recording stops and power off.
☛
This function is not available in DVD recording
EJECT
STANDBY/ON DVD PROG VCR LINE2
3
OK
6
4
4
5
LENGTH 2:30
SET LENGTH :
PRESS REC ●
Before presetting your DVD-VCR:
◆ Switch on both the television and your DVD-VCR
◆ Check that the date and time are correct
◆ Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1 Press the TIMER button.
Result:
The TIMER METHOD is displayed.
2 Press the corresponding or ❷ buttons, until the G-Code option
is selected.
3 Press the ❿ button to select G-Code .
Result: A message is displayed to allow you to enter the
G-Code code.
☛
If all six programmes have been set, the message Timer
is Full is displayed. Refer to page 38 if you wish to
cancel a preset recording.
4 Press the numeric buttons to enter the code opposite the pro
gramme that you wish to record in your television magazine.
➢
If you wish to correct the G-Code code that you are
entering:
◆ Press the ➛ button until the digit to be corrected is
cleared
◆ Enter the correct digit
5 Press the OK button.
Result:
The information concerning the programme is displayed.
☛
When using the G-Code function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or ❷ buttons. Refer to the following page if:
◆ The programme number or times flash
◆ You wish to modify the programme
6 If the programme and times are correct, press the RETURN button.
7 Press the STANDBY/ON button to activate the timer.
8 Refer to page 38 if you wish to:
◆ Check that your VCR has been programmed correctly
◆ Cancel a preset recording
☛
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to programme
your videorecorder instantly with the remote control. Tap
in the G-CODE code for the programme you wish to
record.
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
VCR VCR