Document Outline

• 1.0 Introduction 1
• 2.0 Drive specifications 3
  • 2.1 Specification summary table 3
  • 2.2 Formatted capacity 5
    • 2.2.1 LBA mode 5
  • 2.3 Default logical geometry 5
  • 2.4 Physical organization 5
  • 2.5 Recording and interface technology 5
  • 2.6 Physical characteristics 6
  • 2.7 Seek time 6
  • 2.8 Start/stop times 6
  • 2.9 Power specifications 6
    • 2.9.1 Power consumption 7
    • 2.9.2 Conducted noise 9
    • 2.9.3 Voltage tolerance 9
    • 2.9.4 Power-management modes 9
  • 2.10 Environmental specifications 10
    • 2.10.1 Ambient temperature 10
    • 2.10.2 Temperature gradient 10
    • 2.10.3 Humidity 10
    • 2.10.4 Altitude 10
    • 2.10.5 Shock 11
    • 2.10.6 Vibration 11
  • 2.11 Acoustics 11
  • 2.12 Electromagnetic immunity 12
  • 2.13 Reliability 12
  • 2.14 Agency certification 13
    • 2.14.1 Safety certification 13
    • 2.14.2 Electromagnetic compatibility 13
    • 2.14.3 FCC verification 13
• 3.0 Configuring and mounting the drive 15
  • 3.1 Handling and static discharge precautions 15
  • 3.2 Breather filter hole precautions 16
  • 3.3 Jumper settings 17
    • 3.3.1 Master/slave configuration 17
    • 3.3.2 Cable-select option 17
    • 3.3.3 Alternate capacity jumper 17
    • 3.3.4 Ultra ATA/100 cable 18
  • 3.4 Drive mounting 18
• 4.0 ATA interface 21
  • 4.1 ATA interface signals and connector pins 21
    • 4.1.1 Supported ATA commands 23
    • 4.1.2 Identify Device command 25
    • 4.1.3 Set Features command 28
    • 4.1.4 S.M.A.R.T. commands 29
• 5.0 Seagate Technology support services 31
• Figure 1. Typical 5V startup and operation current profile 8
• Figure 2. Typical 12V startup and operation current profile 8
• Figure 3. Breather filter hole location 16
• Figure 4. Master/slave jumper settings 17
• Figure 5. Ultra ATA cable connectors 18
• Figure 6. Mounting dimensions-top, side and end view 19
• Figure 7. I/O pins and supported ATA signals 22
• 1.0 Introduction
• 2.0 Drive specifications
  • 2.1 Specification summary table
  • 2.2 Formatted capacity
    • 2.2.1 LBA mode
  • 2.3 Default logical geometry
  • 2.4 Physical organization
  • 2.5 Recording and interface technology
  • 2.6 Physical characteristics
  • 2.7 Seek time
  • 2.8 Start/stop times
  • 2.9 Power specifications
    • 2.9.1 Power consumption
      • 2.9.1.1 Typical current profile
    • 2.9.2 Conducted noise
    • 2.9.3 Voltage tolerance
    • 2.9.4 Power-management modes
  • 2.10 Environmental specifications
    • 2.10.1 Ambient temperature
    • 2.10.2 Temperature gradient
    • 2.10.3 Humidity
      • 2.10.3.1 Relative humidity
      • 2.10.3.2 Wet bulb temperature
    • 2.10.4 Altitude
    • 2.10.5 Shock
      • 2.10.5.1 Operating shock
      • 2.10.5.2 Nonoperating shock
    • 2.10.6 Vibration
      • 2.10.6.1 Operating vibration
      • 2.10.6.2 Nonoperating vibration
  • 2.11 Acoustics
  • 2.12 Electromagnetic immunity
  • 2.13 Reliability
  • 2.14 Agency certification
    • 2.14.1 Safety certification
    • 2.14.2 Electromagnetic compatibility
    • 2.14.3 FCC verification
• 3.0 Configuring and mounting the drive
  • 3.1 Handling and static discharge precautions
  • 3.2 Breather filter hole precautions
  • 3.3 Jumper settings
    • 3.3.1 Master/slave configuration
    • 3.3.2 Cable-select option
    • 3.3.3 Alternate capacity jumper
    • 3.3.4 Ultra ATA/100 cable
  • 3.4 Drive mounting
• 4.0 ATA interface
  • 4.1 ATA interface signals and connector pins
    • 4.1.1 Supported ATA commands
    • 4.1.2 Identify Device command
    • 4.1.3 Set Features command
    • 4.1.4 S.M.A.R.T. commands
• 5.0 Seagate Technology support services
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • K
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W