SATO HT200e - Manual (Page 36)

SECTION 2: INSTALLATION AND SETUP
Page 2-18 SATO HT200e
PROCESS ON THE SCREEN FOR USER MAINTENANCE MODE
3 + Power “ON”
Ｐ Ｒ Ｉ Ｎ Ｔ Ｄ Ａ Ｒ Ｋ Ｎ Ｅ Ｓ Ｓ
1 Ｌ １ ２ 3 ４ ５ Ｄ
［ Ｒ Ｅ Ｄ ］
Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｐ Ｅ Ｅ Ｄ
６ ０ ｍ ｍ ／ ｓ ｅ ｃ
８ ０ ｍ ｍ ／ ｓ ｅ ｃ
Ａ Ｕ Ｔ Ｏ Ｐ Ｏ Ｗ Ｅ Ｒ Ｏ Ｆ Ｆ
2 Ｏ Ｎ Ｏ Ｆ Ｆ
Ｓ Ｔ Ａ Ｒ Ｔ － Ｕ Ｐ Ｄ Ｉ Ｓ Ｐ Ｌ Ａ
3 Ｍ Ａ Ｎ Ｕ Ａ Ｌ Ｏ Ｎ Ｌ Ｉ Ｎ Ｅ
Ｉ ／ Ｆ Ｓ Ｅ Ｔ Ｔ Ｉ Ｎ Ｇ
4 ４ ８ ０ ０ ｂ ｐ ｓ ９ ６ ０ ０ ｂ ｐ ｓ
１ ９ ２ ０ ０ ｂ ｐ ｓ
Ｄ Ａ Ｔ Ａ Ｂ Ｉ Ｔ Ｓ Ｅ Ｔ Ｔ Ｉ Ｎ Ｇ
5 ７ ｂ ｉ ｔ ｓ ８ ｂ ｉ ｔ ｓ
Ｐ Ａ Ｒ Ｉ Ｔ Ｙ Ｓ Ｅ Ｔ Ｔ Ｉ Ｎ Ｇ
6 Ｏ Ｄ Ｄ Ｅ Ｖ Ｅ Ｎ Ｎ Ｏ Ｎ Ｅ
Ｐ Ｒ Ｏ Ｔ Ｏ Ｃ Ｏ Ｌ
7 Ｒ Ｅ Ａ Ｄ Ｙ ／ Ｂ Ｕ Ｓ Ｙ
Ｘ Ｏ Ｎ ／ Ｏ Ｆ Ｆ
Ｆ Ｉ Ｘ Ｅ Ｄ Ｆ Ｏ Ｒ Ｍ Ａ Ｔ
8 Ｎ ｏ ［ ・ ・ ］
９ ９ : Ｃ Ｌ Ｅ Ａ Ｒ
Ｃ Ａ Ｌ Ｅ Ｎ Ｄ Ａ Ｒ Ｓ Ｅ Ｔ Ｔ Ｉ Ｎ
9 ０ １ ／ ０ ９ ／ ０ １ １ ３ : ３ ０
Select print density with ［←］and [ → ]and press
[ENTR].
Press [FUN1] key, so that the screen for the density
in 2 colors (Red) can be reached. (RED Display)
Select print speed with ［←］[ → ]
[ ↓ ]and [ ↑ ]and press [ENTR].
(When a battery is used, 60mm/sec is
fixed.)
Select with ［←］and [ → ], and press [ENTR]
(ON: Auto Off Power is available.)
Select start-up screen with ［←］and [ → ], and press
[ENTR]. Manual: After power is “ON”, it displays
the entry for print data.
On-line: After power is “ON”, it displays the receiving
Select communication speed with[ ↓ ] [ ↑ ] [ ← ]
[ → ], and press [ENTR].
(4800bps, 9600bps, 19200bps)
Select protocol with [ ↓ ] [ ↑ ] [ ← ] and [ → ], press
[ENTR]. (READY/BUSY, XON/OFF)
Select parity with [ ←] and [→], and press [ENTR].
(Odd parity, even parity, and no parity)
Select data length with [ ← ] and [ → ], and press
[ENTR]. (7 bit, and 8 bits)
Fix where the format for use needs to be fixed.
Enter the format No. and press [ ENTR]. If [**]
and [ENTR] are pressed, it goes to the process
No. 9.
Note: The format fixed can be released with “99”.
Enter date and time for calendar, and press [ ENTR
(The setting will be made by pressing [ENTR] when
cursor is placed at the minute position. No other
position is NOT permitted.)
When AC adaptor is used: