Samsung DTB-H260F - Manual (Page 7)

10
CHAPTER ONE
Connecting the Set-Top Box
1
11
CHAPTER ONE
Connecting the Set-Top Box
1
1 ANT OUT
Use to connect your TV using a coaxial cable. The
received RF signals from ANT / CABLE IN are bypassed
for analog channels.
2 ANT / CABLE IN
Connect the AIR antenna or CATV antenna here.
Connect the cable in the event that a local cable
provider is passing through 8-level Vestigial Sideband
(8VSB) and Quadrature Amplitude Modulation (QAM)
on their systems.
3 HDMI OUT
Connect the HDMI input of your display using HDMI
cable.
4
This USB port is used for maintenance purpose only.
Please, do not insert USB devices into the port.
5 S-VIDEO OUT
Provides good picture quality. If your TV has S-Video
compatibility, use this jack along with the Video
jacks to connect the Set-Top Box. Use this output for
conventional TV sets that have an S-Video input but
no component video inputs. This output port supports
only the standard definition (SD) output. (OSD not
supported)
6 DTV OUT (COMPONENT)
You can connect Y, P
B
, and P
R
to a TV or another video
component input. As with DTV OUT, 1080i (interlaced
scanning), 720p (progressive scanning), and 480p are
available by setting the RESOLUTION SELECT switch. This
output port supports SD and high definition (HD).
7 VIDEO OUT
If your TV has Video capability, connect this jack to the
video input jack on your TV using a video cable. Use
this output for conventional TV sets that do not have
S-Video or component video inputs. This output port
supports SD only. (OSD not supported)
8 L/R AUDIO OUT
Connect these jacks to the analog audio inputs on
your TV set (i.e., to a TV that has jacks for L/R inputs). Or
connect these jacks to the L/R inputs of a separate audio
component.
9 DOLBY DIGITAL OUT (OPTICAL)
Use to connect the Digital Audio Input on your TV set.
0 RESOLUTION SELECT
Switches between 1080i, 720p, 480p, and 480i formats.
Switches the DTV Component outputs to the following
formats:
• 1080i
Use this setting for an HDTV-ready wide screen (16:9)
aspect ratio TV monitor that can handle the 1080i
video output format.
• 720p
Use this setting for an HDTV-ready wide screen (16:9)
aspect ratio TV monitor that can handle the 720p
video output format.
• 480p
Use this setting for a Digital-ready screen (4:3) aspect
ratio TV monitor with Progressive Scan DTV ready
component video inputs that can handle the 480p
video output format. The TV monitor may be labeled
Enhanced Definition or Progressive Scan, but not
Wide Screen.
• 480i
Use this setting for a conventional TV with regular
video, S-Video, or component video inputs.
! DTV OUT SELECT
Use to select any of Y, P
B
, P
R
and HDMI according to the
video input of the TV or monitor.
NOTE
The use of 1080i on a 4 x 3 monitor or the use of 480p
on a 16 x 9 monitor may cause Aspect Ratio picture
distortion.
Check the TV monitor’s owner’s manual to verify this
capability.
Subscription cable services require service-specific
requirements for viewing.
• SD=Standard Definition (480i)
HD=High Definition (480p, 720p, 1080i)
Rear Panel
1 2 3 4 5 6 7 8 9 0 !
NOTE
In this instruction book, the terms “Set-Top Box” and “STB” are equivalent.
1
Press to turn the power on or off.
2 IR Receiver
Receives IR (Infra-red) signals from the remote
control.
Front Panel
1 2
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. 1992-1997 Dolby Laboratories. All rights reserved.
10-11 2006-10-12 ｿﾀﾈﾄ 1:13:07