Skylink ID-318 - Manual (Page 2)

4. INSTALLATION
You can use the mounting accessories to mount the Motion Sensor on a
wall. First, mount the ball joint on the wall, then slide the Motion Sensor
on the ball joint. You should mount it at a height of about 7ft from the
ground to achieve better coverage.
Walk test should be performed after the motion sensor is mounted. Walk
in the covered area, if motion is detected, a red light inside the sensor
will flash. If the red light does not flash, motion has not been detected and
you may need to re-position the sensor. Ensure you walk test the whole
area that you would like the motion sensor to cover.
Note:
- Perform the walk test after you
have inserted the battery for more
than 1 minute.
- The sensor will not be triggered
by a new motion unless no motion
has been detected for 3 seconds.
Therefore, wait for at least 3 seconds
during walk testing to make a next
movement.
- Disable CDS Light Sensor during
walk test, re-enable it after walk test.
Note:
When installing the motion sensor, avoid placing it near heat or cold
producing devices (i.e. A/C or furnace vents, fans, ovens, space heaters,
etc), and avoid pointing it to the moving objects like a window curtain. Air
movement, especially caused by changes in temperature may trigger the
Motion Sensor. Please carefully test your Motion Sensor so that it will
only be triggered by wanted movement.
M
0 1 2 3 4 5 6 7 8 9 10
2
4
6
8
10
DETECTING AREA: (Unit = meter)
55°
22° 22°
12°
SENSOR
27°
55° 1.2M
11°
5. TESTING AND OPERATION
Walk Test
8. FCC
9. WARRANTY
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
10. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z702
Patent Pending
©2010 SKYLINK GROUP
If the jumper connector is in place,
the light sensor threshold is set to
dark, a motion activation signal will
not turn on the lighting receiver
unless the environment is really
dark.
If the jumper connector is removed,
the light sensor threshold is set to
dim, a motion activation signal will
turn on the lighting receiver even the
environment is not so dark.
You should set the desired light sensing threshold by trial and error.
After setting all the jumper connectors, you may place the battery com-
partment door back on and tighten the screw. You may now mount the
motion sensor at the desired location where movement will be monitored.
3. CUSTOMIZING THE MOTION SENSOR (CONT)
7ft
7. BATTERY
You may erase a transmitter from the receiver module, but you cannot
erase a specific device directly, you must erase all the wireless devices,
then program the ones you want to keep. Follow the instructions below
to erase programmed transmitters.
1. Power off the receiver module.
2. Press the SET button on the Motion Sensor.
3. Press and hold the SET button for at least 2 seconds. Do not release
this button until step 5.
4. Power up the receiver module, you will hear a beep.
5. You may release the SET button.
6. When the button is release, you have successfully erased all the
devices from the lighting receiver.
To erase Motion Sensor from other receivers, please refer to the
instructions of the receivers.
When the LED does not flash (ON then OFF, etc) after the Motion Sensor
is triggered or when the motion sensor does not control receiver after
movement is detected, it is time to replace the battery. Refer to Section 2
to open the battery door.
Note: Dispose of batteries properly.
Erasing Motion Sensor from the Dimmable Receiver Module
model MD-318 or On / Off Receiver Module model MR-318
11. ACCESSORIES
TM The SkylinkHome System consists of many other devices such as
TM SkylinkPad Remotes, Motion Sensor, ON/OFF Wall Switch, Wall Dimmer,
Plug-In Dimmer with or without Repeater, Plug-In ON/OFF Control
(Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, ON/OFF
TM Control, Smart Button Garage Door Control, etc. Please visit Skylink
website at www.skylinkhome.com for more information.
V2.0
6. ERASING MOTION SENSOR FROM RECEIVERS
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.