Sanyo CE52LH1R - Manual (Page 8)

8
■
Advanced settings
Use the 5 or 6 button to select Advanced settings and press
the 1 or 2 button to enter the sub menu as follows.
DCDi(Directional Correlational Deinterlacing) is used to process
moving angled edge in deinterlacing to get the smoothest and most
natural image. Press the 1 or 2
button on the remote control
to select On or Off.
ACC/ACM(ACC: Adaptive Contrast and Color; ACM-II: Active Color
Management-II) is used to select adaptive Brightness, Contrast and
tone control. Press the 1 or 2
button on the remote control to
select suitable mode either Vivid, Cinema, Sport or Off.
CCS(Cross Color Separation) is used to remove residual chroma
information from luminance signal which is the result of imperfect
decoding of composite video. Press the 1 or 2
button on the
remote control to select either Auto, Standard or Off.
DNR(Digital Noise Reduction) is available for noise reduction. Press
the 1 or 2
button on the remote control to select either Auto,
Low, Mid, High or Off.
MPEG NR(MPEG Noise Reduction): Removes unwanted ringing and
block noise from images that have undergone MPEG or JPEG
compression and decompression. Press the 1 or 2
button on
the remote control to select On or Off.
Film Mode(Inverse 3:2 pulldown): Film vs.Video-Detect film.
Performed on material which underwent technologic conversion to
video. Press the 1 or 2
button on the remote control to select
On or Off.
Press the MENU button and select Sound using the 5 or 6
buttons, press the 1 or 2 button to enter.
Select and adjust to obtain the best sound settings for your
environment using the 5 or 6
button to select Treble, Bass or
Balance and the 1 or 2 button to adjust levels.
Bass Expander can also be selected using the 5 or 6 button
and pressing the 1 or 2
button to select On or Off.
These settings automatically store when you exit the menu.
Press the
BACK button to return to the previous menu.
Press the MENU button to exit menu operation.
Press the MENU button and select Time using the 5 or 6
buttons, press the 1 or 2 button to enter. Press the BACK
button to return to the previous menu. Press the
MENU button to exit
menu operation.
✐ If the monitor is switched off by the standby switch 4 on the
back of the LCD monitor the time settings will be cancelled.
■
Current Time
Use NUMERIC buttons [0-9] to set Current time. (00:00~23:59)
To reset the time using the 1 or 2 button.
✐ Other items in Time Menu cannot be selected until Current Time
has been set.
■
Off Time
The Off time will switch the monitor into the standby mode when the
selected time has elapsed.
Use
NUMERIC buttons [0-9] to set Off Time. (00:00~23:59)
To reset the time using the 1 or 2 button.
✐ If the monitor is switched off by the standby button 4 , the timer
settings will be cancelled.
✐ About one minute before the set time is reached, the status of the
monitor will display on the screen.
■
On Time
Once On Time has been set, you will not miss your favourite tv
programme.
Use
NUMERIC buttons [0-9] to set On Time. (00:00~23:59)
To reset the time using the 1 or 2 button.
✐ Once On Time has been set, when the set time is reached, the
monitor will leave the stand-by status and enter to the source
automatically.
✐ After On Time has been set, you can go on watching other
programs. When the set time is reached, the monitor will display
"Note: Time is up!" and then will automatically switch to
the preset program.
■
On Position
✐ On Position can only be selected whenOnTime has been set.
Once On Position has been set, when the set time is reached, the
monitor will enter to the preset source automatically.
Use the 1 or 2
button to select the preset source AV1, AV2,
AV3, PC orDVI.
Press the MENU button and select Setup using the 5 or 6
buttons, press the 1 or 2 button to enter. Press the BACK
button to return to the previous menu. Press the
MENU button to exit
menu operation.
■
Menu Setup
Whenever Setup menu is accessed initially, Menu Setup will be the
default selection. Press the 1 or 2
button to enter the sub
menu.
Language is preset to English.
H-Position changes the OSD position horizontally by using the 1
or 2
button.
V-Position changes the OSD position vertically by using the 1 or
2 button.
Duration is used to set the display time of the MENU by using the
1 or 2 button.(5~120 seconds)
Transparence is used to adjust transparence of menu. Use the 1
or 2
button to adjust levels.
MENU OPERA MENU OPERA TION TION
Sound menu
GB GB
Setup menu
H_Sets
V_Sets
6I\Q^M:M[WT]\QWV @/)
Picture menu
60
Time menu
H_Sets
V_Sets