Sound Storm Laboratories SSV10.4FL - Manual (Page 10)

On a towel or soft cloth, gently place the monitor assembly “face down” on a stable
work surface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Thread all the wires through the
round hole in the center of the
mounting plate.
Install the monitor onto the
mounting plate, using at least six
of the screws provided.
Attach the monitor mounting plate
by screwing through the headliner
and into the existing roof supports
or the wood bracket you made (see
TIP below).
To lower the monitor, press the Monitor Release button and pull the monitor down.
It will drop freely to 45º.
To lower the monitor further, continue pulling down and the internal mechanism
will permit further movement and will hold the monitor in the position in which you
leave it.
To avoid accidental damage, we suggest you always close the monitor assembly
when it is not in use. To do so, rotate the monitor back to a 0º left-to-right position,
and push it up into the monitor base until you hear a “click.” Test that it is secured
by gently pulling down on monitor frame.
VIDEO SOURCE 1
(DVD player,
video game, etc.
)
VIDEO SOURCE 2
(DVD player,
video game, etc.
)
RED
BLACK
to Chassis Ground
DOME LIGHTS
CONTENTS
SSV10.4FL User’s Manual - Contents
U S E R ’ S M A N U A L
SSV10.4FL User’s Manual - page 6
SSV10.4FL User’s Manual - page 7
SSV10.4FL User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV10.4FL User’s Manual User’s Manual - page 3
Monitor Controls and Features
SSV10.4FL User’s Manual - page 4 SSV10.4FL User’s Manual- page 5
Troubleshooting
SSV10.4FL User’s Manual - page 11
Specifications
SSV10.4FL User’s Manual - page 12
Remote Control
SSV10.4FL User’s Manual - page 8
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
NOTE
Hardware shown in this illustration
is not provided due to varying
installation requirements.
2 General precautions
2 Safety precautions
3 Installation precautions
3 Operation precautions
3 Features
3 What is included?
4 Monitor controls and features
5 Remote control
5 Remote control battery replacement
6 System wiring
7 Monitor installation
8 Releasing and opening the monitor
9 Powering up the monitor
9 Turning on the dome lights
10 On screen menu system
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV10.4FL
10.4" Flip Down TFT Monitor
A/V SYSTEM
Screen size
Video Compatibility
LCD panel type
Resolution, pixels
Brightness
GENERAL
Operating voltage
Dimensions (L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
This monitor incorporates an on-screen menu display systems which permits you
to setup the monitor for a wide variety of installations and applications.
Enter the menu system by pressing the MODE button on the front of the monitor
or the remote control. Pressing the MODE button steps you through the five main
screens of the menu system. These are, in order: Color, Picture, OSD (On Screen
Display) Menu, Miscellaneous and Exit.
The basic navigation method for this menu system is to:
1 - enter a menu by pressing the MODE button
2 - use the < and > buttons to scroll to the parameter you wish to change
3 - press the MODE button to confirm the selection
4 - use the < and > buttons to adjust the parameter you wish to change
5 - press the MODE button to enter the selection
To leave a menu:
1 - press MODE to move to another menu
2 - press MODE a few times until you arrive at the EXIT screen
3 - wait about 15 seconds, after which time the monitor exits the system automatically.
SSV10.4FL User’s Manual - page 10
On-screen (OSD) menu system
Each of the three main menu areas contain submenus permitting you to adjust
many aspects of your monitor's behavoir.
In the COLOR menu, you can adjust the following:
CONTRAST • BRIGHTNESS • HUE • SATURATION
In the OSD menu, you can adjust the following:
LANGUAGE (language used in the menus)
OSD-H and OSD-V (position of image on monitor screen)
OSD-TIMER (length of time OSD system remains present after last activity.
ON means 5 seconds, OFF means OSD will stay on until you exit the system.
TRANSLUCENT (controls if menu background is opaque or translucent. After
selecting this function, use the < and > keys to turn translucency on or off).
In the MISCELLANEOUS menu, you can adjust the following:
SIGNAL SOURCE (permits you to switch between A/V input sources 1 and 2. After
selecting this function, use the < and > keys to choose the input source).
RESET (YES means return monitor to factory defaults, NO means keep custom
settings you have created).
Sub-menus in the OSD system
VIDEO INPUT 1
(YELLOW)
FUSE
BLACK VIDEO INPUT 2
(WHITE)
Push the monitor
release button forward
Pull the monitor screen
down to the desired angle