Samson Servo 120 - Manual (Page 2)

Output Power (typical all channels driven):
4
Ω
, 1 kHz, 1% THD, 83 W
4
Ω
, 1 kHz, .034% THD, 60 W
8
Ω
, 1 kHz, 1% THD, 57.5 W
8
Ω
, 1 kHz, <.019% THD, 52 W
8
Ω
bridged, 1 kHz, 1% THD, 160 W
8
Ω
bridged, 1 kHz, < .08% THD, 120W
Frequency Response (-3 dB): <10 Hz to 100 kHz
Frequency Response (1 watt): 20 Hz to 20 kHz, -0.1/-0.2
Crosstalk (adj. channels): 80 dB, 1 kHz @ rated output
Distortion (THD+N, 20 Hz to 20 kHz) (80 kHz LPF):
at rated power: < .05%
at 1 watt: < .05%
Sensitivity (level control at maximum): +4 dBu
Damping Factor (8
Ω
): > 150
Dynamic Range: 98 dB below rated output
(20 Hz to 22 kHz B.P.F.)
Headphone Output Level: 240 mW at 8
Ω
(1 kHz)
Input Impedance: >10 k
Ω
balanced/> 10 k
Ω
unbalanced
Power Consumption: 240 W @ 120 V/60 Hz
270 W @ 220 V/50 Hz
Dimensions: 17.5
″
(w) x 1.75
″
(h) x 11.5
″
(d)
444 mm (w) x 44 mm (h) x 292 mm (d)
Weight: 15.6 lb / 7 kg
SERVO 120 SPECIFICATIONS
5.0000
4.0000
3.0000
2.0000
1.0000
0.0
-1.000
-2.000
-3.000
-4.000
-5.000
10 100 1k 10k 50k
Ap
AUDIO PRECISION Servo 120 LEVEL (dBr) vs FREQ (Hz)
0dB ref
ARCHITECT’S & ENGINEER’S
SPECIFICATION
The power amplifier shall be capable of stereo or
mono bridged operation. In stereo mode, it shall deliver a
minimum of 52 W into loads of 8 ohms each with both chan-
nels operating, or 60 W into loads of 4 ohms each with both
channels operating. In mono bridge mode, it shall deliver a
minimum of 120 W into an 8 ohm load. It shall be passively
cooled, and shall have internal short-circuit and thermal pro-
tection circuitry. A protection LED indicator shall activate
and the power amplifier shall shut down to protect against
short circuits, overheating, severe overcurrent conditions or
DC offset present at the outputs. The power amplifier shall
have slow start-up and muted inputs on turn-on. Inputs
shall be on balanced 1/4
″
tip-ring-sleeve connectors and
outputs shall be on 1/4
″
phone connectors and on push-
spring terminals. The front panel shall have independent level
controls for left and right channels, a master power switch
and LED indicators for clip, idle and amplifier protection.
The power amplifier shall have a frequency response
of less than 10 Hz to 100 kHz, signal-to-noise equal to or
greater than 103 dB and THD less than 0.5%. Total power
consumed at full audio power shall be 240 W (120 Vac)
and 975 W (220 Vac). The dimensions shall allow for stan-
dard 19
″
EIA rack mounting. It shall be 1.75
″
(44 mm; 1
rack space) high and 11.5
″
(292 mm) deep. Weight shall be
15.6 lb. (7 kg). The power amplifier shall carry a three-year
warranty.
The power amplifier shall be a SAMSON SERVO 120.
Specifications subject to change without notice. ©1998 Samson
FREQUENCY RESPONSE