Sanyo CE42LM6WP - Manual (Page 9)

9
MENU OPERATION
Picture menu
n Advanced settings
Use the 5 or 6 button to select Advanced settings and press
the 1 or 2 button to enter the sub menu as follows .
DCDi (Directional Correlational Deinterlacing) is used to process
moving angled edge in deinterlacing to get the smoothest and most
natural image . Press the 1 or 2
button on the remote control to
select On or Off .
ACC/ACM (ACC: Adaptive Contrast and Color; ACM-II: Active Color
Management-II) is used to select adaptive Brightness, Contrast and
tone control . Press the 1 or 2
button on the remote control to
select suitable mode either Vivid, Cinema, Sport or Off .
CCS (Cross Color Separation) is used to remove residual chroma
information from luminance signal which is the result of imperfect
decoding of composite video . Press the 1 or 2
button on the
remote control to select either Auto, Standard or Off .
DNR (Digital Noise Reduction) is available for noise reduction . Press
the 1 or 2
button on the remote control to select either Auto,
Low, Mid, High or Off .
MPEG NR (MPEG Noise Reduction): Removes unwanted ringing and
block noise from images that have undergone MPEG or JPEG com-
pression and decompression . Press the 1 or 2
button on the
remote control to select On or Off .
Film Mode (Inverse 3:2 pulldown): Film vs .Video-Detect film . Performed
on material which underwent technologic conversion to video . Press the
1 or 2 button on the remote control to select On or Off .
Sound menu
Press the MENU button and select Sound using the 5 or 6 but-
tons, press the 1 or 2 button to enter .
Select and adjust to obtain the best sound settings for your environ-
ment using the 5 or 6
button to select Treble, Bass or Balance
and the 1 or 2 button to adjust levels .
Bass Expander can also be selected using the 5 or 6 button
and pressing the 1 or 2
button to select On or Off .
These settings automatically store when you exit the menu .
Press the
BACK button to return to the previous menu .
Press the MENU button to exit menu operation .
Time menu
Press the MENU button and select Time using the 5 or 6 but-
tons, press the 1 or 2 button to enter . Press the BACK button
to return to the previous menu . Press the
MENU button to exit menu
operation .
n Current Weekday
Use to set current weekday using the 1 or 2 button .
n Current Time
Use to set the current time using the Numeric buttons .
✐
Other items in Time Menu should not be selected until Current
Time has been set .
n Schedule
Use to set up to 20 separate time schedules for “Power On” or “Power
Off”, select 1 ~ 20 using the 1 or 2
button .
n Weekday
Use to set the schedule for “Power On” or “Power Off” of any weekday
from Sunday through to Saturday or Everyday using the 1 or 2
button .
n Time
Use to set the schedule for “Power On” or “Power Off” of any time
using the Numeric buttons .
n Action
Use to set the schedule for “Power On” or “Power Off” active using
the 1 or 2
button .
You can set Power On timer in Time menu selecting “ON” in “On
Timer Function” in Installation Mode . If it is selected “OFF”, Power On
display in Time menu does not functional .
n On Program
Use to select AV1, RGB, AV2, AV3, PC, DVI or Network for the
schedule of “Power On” using the 1 or 2 button .
n Active
Use to select ON or OFF using the 1 or 2 button . When set
“OFF” the above items “Schedule”, “Weekday”, “Time”, “Action” or
“ON Program” will be inactive .
Use
NUMERIC buttons [0 ~ 9] to set On Time . (Action “Power On” –
00:00 ~ 23:59)
✐
Once On Time has been set, when the set time is reached, the
monitor will leave the stand-by status and enter to the source
automatically .
✐ After On Time has been set, you can go on watching other pro-
grams . When the set time is reached, the monitor will automatically
switch to the preset program .
✐ On Program can only be selected whenAction (Power On) has
been set .
✐ Action (Power Off) can be set to turn the monitor into standby at a
selected time
Once On Program has been set, when the set time is reached, the
monitor will enter to the preset source automatically .
Use the 1 or 2
button to select On program, AV1, RGB, AV2,
AV3, PC, DVI or Network .
Setup menu
Press the MENU button and select Setup using the 5 or 6 but-
tons, press the 1 or 2 button to enter . Press the BACK button
to return to the previous menu . Press the
MENU button to exit .
n Menu Setup
Whenever Setup menu is accessed initially, Menu Setup will be the
default selection . Press the 1 or 2
button to enter the sub menu .
GB GB