Siemens AC75 - Manual (Page 270)

AC75 AT Command Set
10.3 AT^SISS
s
AC75_ATC_V01.002 Page 270 of 569 10/30/06
Confidential / Released
Parameter value; type and supported content depend on related
<srvParmTag>
.
Supported Internet service type values in
<srvParmValue>
for
<srvParmTag>
value "srvType".
Before changing the "srvType" of an existing service profile be sure that the profile is closed. To verify the con-
nection state of the service profile enter the read command
AT^SISI
. Only when
<srvState>
=2 is returned
for this specific service profile you can change its service type.
“Socket“
AC75 acting as client or server (listener) for TCP or UDP.
If AC75 is listener at least two service profiles are required. The first socket pro-
file must be configured as listener. The second service profile will be dynami-
cally assigned when a socket connection request from a remote client is
incoming. For this purpose, one service profile must be left free (= not config-
ured with
AT^SISS
). An incoming socket connection request will be indicated
by the "
^SIS
" URC, with the next free
<srvProfileId>
shown inside the
URC as parameter
<urcInfoId>
. The connection request can be accepted
or rejected by using the commands
AT^SISO
or
AT^SISC
and the ID retrieved
from the "
^SIS
".
“Ftp“ AC75 acting as FTP client.
“Http“ AC75 acting as HTTP client.
“Smtp“ AC75 acting as SMTP client.
“Pop3“ AC75 acting as POP3 client.
“none“ Reset Internet service profile settings. Operation is not allowed if profile is in
use, i.e. it was activated via
AT^SISO
.
Supported string parameter character set selections in
<srvParmValue>
for
<srvParmTag>
value "alphabet".
[“0“] Applicable character set is determined by current setting of
AT+CSCS
.
“1“ International Reference Alphabet (IRA, seven bit ASCII).
Supported POP3 user command values in
<srvParmValue>
for
<srvParmTag>
value "pCmd".
1 Status command.
This command retrieves the "drop listing" of a POP3 server. A "drop listing"
consists of a single line containing the number of messages in the maildrop list
followed by the total size of the maildrop list in bytes. Each drop listing will be
finished by a so-called "dotline", i.e. a new line with just a single dot.
2 List command.
If
<srvParmTag>
value "pNumber" is set to a non-zero value the "List" com-
mand returns the "scan listing", consisting of a single line which contains the
message number and the message size in bytes if the specified message
exists in the maildrop list on the POP3 server.
If no such message exists on the server than the POP3 service issues an error
response to the user.
If
<srvParmTag>
value "pNumber" is zero the "List" command returns a multi-
line "scan listing". For each message on the maildrop list of the server the
POP3 service returns a line containing the message number and its size in
bytes. A final "dotline" will be printed at the end of the "scan listing".
If there are no messages on the maildrop list of the server, the POP3 service
returns a positive response, i.e. it doesn't issue an error response, but the
"scan listing" will be empty.
In either case, each scan listing will be finished by a so-called "dotline", i.e. a
new line with just a single dot.
<srvParmValue>
(str)
<srvParmValue-srvType>
(str)
<srvParmValue-alphabet>
(str)
<srvParmValue-pCmd>
(num)