Sharp CD-DH950P - Manual (Page 11)

E-10
Listening to the radio
ON/STAND-BY
DISPLAY
(TV OUT)
DISPLAY
TUNER(BAND) TAPE
AUDIO IN USB
X-BASS
TUNING VOL
FOLDER
CLOCK/TIMER
DEMO
MUTE
DIMMER CLEAR SLEEP
MEMORY
PRESET
PRESET
ENTER
PLAY MODE
BASS/TREBLE
MENU
CD
1 2 3 4 5
4
5
3
2
1
MINI COMPONENT SYSTEM
OPEN / CLOSE
TUNING PRESET
USB AUDIO IN
TAPE
TUNER
CD
TIMER
iPod/iPhone
POWER ON/ STAND-BY
(BAND)
VOL. VOL.
REMOTE
SENSOR CD-DH950P
OPEN / CLOSE
TAPE
TUNER
(BAND)
PRESET
TUNING
TUNING
TUNER(BAND)
PRESET
PRESET
MEMORY
TAPE
Tuning Q
Press the ON/STAND-BY button to turn the power on. 1
Press the TUNER (BAND) button repeatedly to select 2
the desired frequency band (FM or AM).
Press the TUNING ( 3 or ) button to tune in to the
desired station.
Manual tuning:
Press the TUNING ( or ) button as many times as
required to tune in to the desired station.
Auto tuning:
When the TUNING ( or ) button is pressed for more
than 0.5 seconds, scanning will start automatically
and the tuner will stop at the fi rst receivable broadcast
station.
Notes:
When radio interference occurs, auto scan tuning may O
stop automatically at that point.
Auto scan tuning will skip weak signal stations.
O
To stop the auto tuning, press the TUNING ( O or )
button again.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the “ST” O
indicator.
“
O ” will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) O
button to extinguish the “ST” indicator. The reception
changes to monaural, and the sound becomes
clearer.
Memorizing a station Q
You can store 40 AM and FM stations in memory and
recall them at the push of a button. (Preset tuning)
Perform steps 1 - 3 in “Tuning”. 1
Press the MEMORY 2
button to enter the
preset tuning saving
mode.
Within 30 seconds, press the PRESET ( 3 or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
Within 30 seconds, press the MEMORY button to 4
store that station in memory. If the “MEMORY” and
preset number indicators disappear before the station
is memorized, repeat the operation from step 2.
Repeat steps 1 - 4 to set other stations, or to change 5
a preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a
few hours should there be a power failure or the AC power
cord become disconnected.
To recall a memorized station Q
Press the PRESET ( or ) button for less than 0.5
seconds to select the desired station.
To scan the preset stations Q
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
Press the PRESET ( 1 or ) button for more than
0.5 seconds. The preset number will fl ash and the
programmed stations will be tuned in sequentially, for
5 seconds each.
Press the PRESET ( 2 or ) button again when the
desired station is located.
To erase entire preset memory Q
Press the ON/STAND-BY button to enter the stand-by 1
mode.
While pressing down the OPEN / CLOSE button and 2
TUNING button, press the TUNER (BAND) button
until “TUNER CLEAR” appears.
OPEN / CLOSE
TAPE
TUNER
(BAND)
TUNING
CD-DH950P_US_EN.indd 10 CD-DH950P_US_EN.indd 10 2/21/2011 12:13:25 PM 2/21/2011 12:13:25 PM