Samson 115XL - Manual (Page 3)

About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance
are wired in "Parallel", the total imped-
ance is cut in half and when two speak-
ers are wired in “Series,” the total
impedance is the sum of the speakers
individual impedance.
The 115XL impedance is 8 Ohms.
So, when two
115XL ’s are connected
together in parallel, the total impedance
is 4 Ohms. The impedance of your
speaker also has an effect on your
amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
IMPORTANT : There is a minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
Connecting the 115XL to Your Amplifier
The 115XL connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the 115XL’s rear
jackplate.
Using the EXTENSION Output
The 115XL provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook up
with your amplifier. Follow the steps
below to connect two 115XL ’s using
the Extension Output. Connect the
Amplifier Output to the Input of the first
115XL. Now, connect the Extension
Output to the Input of the second
115XL.
4.5XL BASS CABINET
400 WATTS
Hartke
8 EXTENSION
INPUTS
MADE IN CHINA SERIAL NUMBER
Hartke Systems Distributed worldwide by Samson Technologies
www.hartke.com
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000 200 WATTS 8 = 120 WATTS 4 = 200 WATTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLED IN R.O.K. SERIAL NUMBER
115
~ AC INPUT 115V/230V 50/60Hz FUSE 5A/250V, 180W (115V) 2.5A/250V, 450W (230V)
SPEAKER OUTPUTS
8 8 ON OFF HPF
EFFECT
SEND RETUIRN
8
Connecting the 115XL
4.5XL BASS CABINET
400 WATTS
Hartke
8 EXTENSION
INPUTS
MADE IN CHINA SERIAL NUMBER
Hartke Systems Distributed worldwide by Samson Technologies
www.hartke.com
4.5XL BASS CABINET
400 WATTS
Hartke
INPUTS
Hartke Systems Distributed worldwide by Samson Technologies
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000 200 WATTS 8 = 120 WATTS 4 = 200 WATTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLED IN R.O.K. SERIAL NUMBER
115
~ AC INPUT 115V/230V 50/60Hz FUSE 5A/250V, 180W (115V) 2.5A/250V, 450W (230V)
SPEAKER OUTPUTS
8 8 ON OFF HPF
EFFECT
SEND RETUIRN
8