Enforcer, Dimensions, Specifications parts list – SECO-LARM USA Enforcer EV-122C-DVAVQ User Manual

Page 2: Ball-mount indoor/outdoor ir camera manual

Advertising

ENFORCER

Ball-Mount Indoor/Outdoor IR Camera Manual

ENFORCER

Ball-Mount Indoor/Outdoor IR Camera Manual

Dimensions:

Before Starting:

1. Please read this manual carefully and keep it for future

reference.

2. Use the camera within given temperature and electrical limits.
3. While the camera is weatherproof to IP66 standard, do not

mount the camera where it is exposed to rain or other moisture,
or in humid or dusty places.

4. Do not point the camera at the sun. Heat could damage the

camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation, strong

Installation:
1. Run a 12VDC power supply wire and a video cable with a male

BNC connector through the wall to where the camera is to be
mounted.

2. Loosen the set screws with the included hex wrench and remove

the case from the base.
NOTE - The camera ball is NOT attached to the case or the
base. It sits loose inside the case. Therefore, be very careful
when removing the case from the base to not drop the camera
ball.

3. Mount the base to the wall using the four included mounting

screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use the included plastic screw anchors.

4. Run the camera's BNC and power connectors through the

camera base, and connect to the video and power wires that

magnetic fields, or strong electrical signals.*

6. Do not open or disassemble the camera. There are no user-

serviceable parts inside.

7. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic

fields close to the display CRT, especially when the monitor
is turned on or during de-Gaussing, which occurs
automatically with many monitors when the monitor is turned
on.

were run through the wall.

5. Put the case over the camera ball onto the base, being careful to

not drop the camera ball.

6. Holding the case loosely on the base, turn the camera ball to the

desired direction.

7. Once the camera ball is in the desired direction, tighten the set

screws with the included hex wrench. However, do not tighten
them too tightly. Tighten just enough so that the case does not
move, and the camera ball does not rotate.

8. Use the included small screwdriver to adjust the zoom and the

focus of the camera ball if needed, via the holes marked
"ZOOM" and "FOCUS" on the top of the camera ball.

9. Do a final test of the video camera and the monitor.

Specifications

Parts List

1 x Camera Ball
1 x Case
1 x Base
4 x Screws with wall anchors
1 x Small screwdriver
1 x Hex wrench
1 x Manual

1 x DC plug to terminal jack

Case

Camera

Ball

Base

4 x

Screws

Power

Connector

BNC

Connector

_______________________________________________________________________________________________________________________________________________________________

” (118mm)

”

(100mm)

Focus

Zoom

(Use included small screwdriver to adjust zoom and focus.)

EV-122C-DVAVQ

Ball-Mount Color Dome Camera

1/3” CCD, Sony

420 TV lines

510 x 492 pixels

2:1 interlace, V: 59.94Hz, H: 15.734KHz

Internal

1V p-p composite output, 75 ohms

Varifocal 4mm~9mm, F1.6

36 x LEDs (850nm)

Up to 100’ (30m)

~90

beam spread

0.3 lux (0 lux with IR on)

0.45

>48dB

Auto Electronic Shutter (AES), 1/60~1/100,000 sec.

Auto

12VDC ±10%

150mA (IR off), 500mA (IR on)

4°~122° F (-20°~50° C)

IP66 weatherproof

” x 3

” (118 x 100mm)

1.7 lb. (752g)

34” (86cm)

Type

Chip

Resolution

Pickup elements

Scanning system

Sync

Video output

Lens

IR LEDs

IR distance

IR view angle

Minimum illumination

Gamma correction

S/N ratio

Shutter control

Automatic gain control

White balance

Power source

Power consumption

Operating temperature

Enclosure

Dimensions

Weight

Cable length

Advertising

Popular Brands

Popular manuals