Kenwood C-V751 - Manual (Page 11)

11
System connection
ON/STANDBY
PHONES INPUT
TAPE 2
/ MONITOR
VOLUME CONTROL
DOWN UP
TIMER
MODE RDS
PTY DISPLAY CLOCK TA/NEWS
DTS
A.MEMO AUTO BAND
TUNING
PTY SELECT
LISTEN
MODE MULTI.CONTROL
LEVEL
OPEN/CLOSE
SOUND INPUT MODE DIGITAL CIRCLE
SURROUND TIMER
SET DIGITAL REC MODE SET UP
KHz TIMER 1 2 TAPE2/MONI.
F M
LW
MW
AUTO STEREO
MEMO. TUNED
MUTE
RDS EON TP
PTY TA NEWS
CLIP
PRO LOGIC 3 STEREO A M
MHz SLEEP DOWN MIX
AUTO SOUND
CS DTS DOLBY DIGITAL
DIGITAL REC
L C R
LS RS
LFE SW
S
% ¶
7 3 1 2 ! 6 9 0 8 @ #
§ $ ^& * ) ¡ ( ™ £ ¢ ∞
4 5
The keys which have the same names as the controls on the
remote control unit provide the same functions as them.
@MULTI. CONTROL key R
Press to select various setting modes.
These keys are also used in the clock adjust-
ment and timer operations.
#GRC transmitter
Outputs the signals transmitted to the
Graphical Remote Control.
$PHONES jack •
For use in headphones listening.
%INPUT SELECTOR keys 0
Press to select the input.
^TAPE 2/MONITOR key •
For use in monitoring of recording, etc.
&TIMER MODE key T
Press to switch the timer modes.
*CLOCK key R
Press when setting the clock.
(RDS DISPLAY key ·
Press to switch the RDS display.
)RDS PTY key e
For use during reception of RDS broadcast-
ing.
1 (ON/STANDBY) key/indicator
0
Press to switch between ON and STANDBY.
2Remote sensor
3TIMER SET key
T
Press to set the timer function.
4DIGITAL REC MODE key ›
Use to select the DIGITAL REC mode.
5SET UP key £
Use to select the surround sound settings.
6SOUND key ª
Use to adjust the sound quality and ambi-
ence effects.
7INPUT MODE key *
Use to switch between the digital and analog
inputs.
8 DIGITAL key p
Use to select the Dolby digital mode.
9DTS key p
0CIRCLE SURROUND key p
!LISTEN MODE key p
Use to select the listening mode.
¡RDS TA/NEWS key y
For use during reception of RDS broadcast-
ing.
™A.MEMO key ‚
Press when using the auto memory func-
tion.
£AUTO key 0°
Press to select the tuning mode.
The auto tuning or manual tuning mode can
be selected.
Pressing and holding this key for more than
2 seconds changes the MD input display to
TAPE 1 display or the DVD input display to
DVD 6ch INPUT or LD display.
¢BAND key °
Press to switch the broadcasting band.
∞TUNING keys (
, )
°
Press to select the radio station to be re-
ceived.
§OPEN/CLOSE key 0
¶VOLUME CONTROL knob •
Memory indicator
RDS indicators
Frequency display, input selector
display, preset channel display,
surround mode display
DTS indicator CS indicator
DIGITAL indicator
REC indicator
TAPE 2/MONI. indicator
AUTO indicator
STEREO
indicator
TUNED indicator
MUTE indicator
DOWN MIX indicator
SLEEP indicator
PRO LOGIC
indicator
3 STEREO indicator
STEREO indicator
Receiving frequency
unit indicators
Display
Standby mode
While the standby indicator of the unit is lit, a small amount of current is flowing into the unit’s internal circuitry to back up the memory. This condition
is referred to as the standby mode of the unit. While the unit is in the standby mode, it can be turned ON from the remote control unit.
TIMER
indicators Broadcast band indicators
(AM : Australia only)
Speaker selection
indicators
Input channel
indicators
Output channel
indicators
SOUND indicator
DOLBY DIGITAL indicator
CLIP indicator
AUTO tuning mode
Controls and indicators