KORG AX5G User Manual
Page 3
AX3-Series EasyStart
3
Note:
The effect chart printed on the face of your AX5G and B will be indispensable in locating and identifying the various
available effect choices. There is also a more detailed chart in the back of the included manual.
3.
Use the Value Knob to adjust the FX’s main parameter.
4.
To fine tune the sub-parameters (not applicable to LEVEL, NR, CAB, MIC & BODY, TONE, and NOTCH), set the Function Knob to the
corresponding effect type “PARAM” position (the next position moving clockwise on the knob). Choose the desired parameter with the
Write (“UP”) & Cancel (“DOWN”) Buttons and use the Value Knob to adjust the parameter value.
Note:
A list of effect parameters can be found in the aforementioned effect chart in the rear of the manual. This will be
very helpful in determining which parameter is being adjusted.
Tip:
The Original Value Indicator (small dot in the lower right corner of the Program/Value Display) can be used to
indicate the saved effect parameter settings of the currently selected program. Simply put, when the Original Value
Indicator is lit, the previously saved effect parameter setting has been selected.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
(
(
a
a
l
l
l
l
A
A
X
X
5
5
m
m
o
o
d
d
e
e
l
l
s
s
)
)
1.
Select MOD with the Function Knob.
2.
Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “F2” (CL Flange). Then use the Value Knob to adjust the CL Flange
effect’s Main parameter (SPEED).
3.
Turn the Function Knob clockwise one position to PARAM. Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “P2”
(DEPTH). Use the Value Knob to adjust the level of the DEPTH parameter.
Note:
In this mode, if you press the Program Up (Value) switch, the current parameter value will be displayed. If you
press the Program Down (Type/Param) switch, it will display to the currently selected FX type/parameter.
S
S
a
a
v
v
i
i
n
n
g
g
a
a
P
P
r
r
o
o
g
g
r
r
a
a
m
m
You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program:
1.
Set the Function Knob to the “WRITE” position, and press WRITE (“UP”) Button. A User program number will blink in the
Program/Value Display.
2.
Use the Program Up and Down Switches or Value Knob to select the destination program number (1 - 40)
3.
Press the WRITE (“UP”) Button once again, and your program will be stored in the specified location (“CP” will display briefly indicating
the process is complete).
A
A
m
m
p
p
/
/
L
L
i
i
n
n
e
e
S
S
e
e
t
t
t
t
i
i
n
n
g
g
(
(
A
A
X
X
5
5
G
G
o
o
n
n
l
l
y
y
)
)
The AX5G’s output may be optimized to suit specific monitoring sources via the Amp/Line setting. Amp/Line settings can be
made under the P5 parameter of the Drive/Amp (Note; the amp line setting is only applicable to Amp models {i.e. A0, A1,
A2, A3, etc.} and will not be found on Drive models {i.e. D0, D1, D2, D3, etc.}). Select “A1” if you connect the AX5’s output
to the input of a clean-sounding open back combo. Select “A2” if you connect the AX5’s output to the input of an open back
combo with stronger mid-range content. Select “A3” if you connect the AX5’s output into a sealed back cabinet such as an
amp stack. Select “Ln” if you connect the AX5’s output into a line input such as a mixer, recorder, headphones or any other
full range monitoring source.