KORG TRITON Le Electric Keyboard - Manual (Page 8)

PROG
1.1
2.1
2.2
3.1
4.1
4.2
5.1
5.2
5.3
6.1
7.1
7.2
1
PROG
1.1
2.1
2.2
3.1
4.1
4.2
5.1
5.2
5.3
6.1
7.1
7.2
1. Program mode
Use the following procedure to select the desired page from
within the current mode.
1 Press the [MENU] key to access the “PAGE MENU.”
The “PAGE MENU” will show an abbreviated name for
each page.
2 Use the [F1]–[F7] keys at the bottom of the page to select
the desired page. Pressing the same key repeatedly will
scroll through the various sub-pages. You can also move
by using the cursor keys [
], [ ], [ ], [ ].
3 Press the [F8] (“Open”) key to access the page.
4 If the selected page contains two or more tab pages, press
the nearest [F1]–[F7] key below the tabs to select the
desired page.
Other ways to select a page
• You can also move to the desired page by holding down
the [MENU] key and using numeric keys [0]–[9] to enter
a two-digit page number. For example if you wish to
access the 5.3: Ed-LFOs page, hold down the [MENU]
key and consecutively press numeric keys [5] and then
[3].
• By holding down the [MENU] key and using the cursor
keys [ ](–) or [ ](+), you can step through the pages
forward or backward in the order of 1.1 → 2.1 → 2.2 → 3.1,
etc.
In this display page you can select and play programs.
All MIDI data in PROG 1.1: Play is transmitted and
received on the Global MIDI Channel (☞GLOBAL 2.1–
1a).
1.1–1: Program
1.1–1a: Bank, Program Select, Category, Cat. Hold,
10’s Hold, (Tempo)
Bank [Bank A...D, G, g(d)]
This is the program bank display.
Use the BANK [A]–[GM] keys to select the bank.
Bank G will toggle between the GM and g(d) banks each
time you press the BANK [GM] key.
G → g(d) → G → g(d) → G…
The TRITON Le provides rewritable banks A, B, C, and D,
each containing 128 programs (total 512). As for non-rewrit-
able program areas, it provides banks G (capital programs
for GM), and bank g(d) (drums). (☞For a list of the factory-
set programs, refer to the separate VNL.)
PROG PAGE MENU
Play 1.1: Play Select and play programs. Use the Per-
formance Editor for easy editing, and to
do simple editing of arpeggio patterns.
(
☞ p.1)
Basic 2.1: Ed-Basic Set basic program parameters such as
Oscillator and Multisample. (
☞ p.5)
Ctrl 2.2: Ed-Ctrl Controller settings. ( ☞ p.9)
Pitch 3.1: Ed-Pitch Pitch settings. Pitch EG settings.
(
☞ p.10)
Flt1 4.1: Ed-Filter1 Filter 1 (tone) settings. Filter EG set-
tings. (
☞ p.13)
Flt2 4.2: Ed-Filter2 Filter 2 (tone) settings. Filter EG set-
tings. (
☞ p.18)
Amp1 5.1: Ed-Amp1 Amp 1 (volume) settings. Amp EG, pan
(position) settings. (
☞ p.18)
Amp2 5.2: Ed-Amp2 Amp 2 (volume) settings. Amp EG, pan
(position) settings. (
☞ p.22)
LFO 5.3: Ed-LFOs Type and speed settings etc. for the
two LFOs provided for each oscillator.
(Make settings in the pitch, filter, and
amp pages to specify the depth of the
LFO settings you make here.) (
☞ p.22)
Arp 6.1: Ed-Arp. Arpeggiator settings. (Shared with 1.1:
Play parameters. You may edit either.)
(
☞ p.24)
IFX 7.1: Ed-InsertFX Select the BUS and master effect send
level for the oscillator output.
Insert Effect routing, selection and set-
tings. (
☞ p.26)
MFX 7.2: Ed-MasterFX Master Effect selection and settings.
Master EQ settings. (
☞ p.28)
PROG 1.1: Play
Bank A
for preloaded programs
Bank B
Bank C
Bank D000~063
Bank D064~127 For user programs (programs that use multisam-
ples created in Sampling mode (when the sepa-
rately sold EXB-SMPL option is installed))
Bank G GM capital program
Bank g(d) GM drums program
1.1–1a
1.1–1b
1.1–1c