Kustom Wav 1000 - Manual (Page 8)

35
36
ON
OFF
POWER
FUSE: T2A / 250V
AC FUSE
120V 60Hz 160W
ATTENTION
CAUTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DESIGNED IN USA MADE IN CHINA
SERIAL NUMBER
MODEL wAv 1000
CAUTION
CHASSIS SURFACE HOT SUPERFICE DE CHASSIS CHAUDE
ATTENTION
FOOTSWITCH LEFT
Line Out
RIGHT
Line Out PREAMP
Out
POWER
AMP IN
PREAMP
Out
POWER
AMP IN
LEFT RIGHT
34 29
30
31 33 TAB
SPEAKER OUT
32
LEFT RIGHT
Power ON/OFF Switch:
AC Power Cord Receptacle:
Speaker Output Jacks:
Footswitch Jack
Left and Right Line Out:
Left and Right Preamp out:
Left and Right Power Amp In
:
:
Turns AC power on and off.
Insert the AC cord (provided) firmly into the AC
connector. NOTE: Replace the AC power cord if
protective jacket is damaged or ground pin is
damaged or removed.
The fuse is located in a housing just below the
receptacle. Replace only with same type and size.
To remove the fuse, remove AC power cord and
pull out on the tab
above the fuse symbol located
on the fuse carriage. Place the new fuse in the
carriage clip and re-insert. NOTE: To prevent an
electrical hazard, DO NOT replace fuse without
using the fuse carriage. Replace the fuse carriage if
lost or damaged before re-inserting the AC power
cord.
These jacks are used to connect external speakers to
the head. Each channel has 2 jacks wired in parallel
that function the same.
connect a left and
right output to a single mono cabinet. This will
cause the amp to load itself, overheat, distort and
shut down. It is not recommended to load either
channel below 4 ohms because it will not produce
maximum output and may cause overheating and
shutting down.
For best results, connect external speakers using
one of the following methods.
Connect a speaker
cable from one of the left output jacks on the
amp to the left input jack on the cabinet. Repeat
for the right channel. This puts an 8 ohm
load/per channel on the amp. You can add
speakers using the other jacks as long as they are
not lower than 8 ohms per channel.
Connect a speaker cable from one of the LEFT
SPEAKER OUT jacks on the amp to the
MONO Jack of the WAV 412 cabinet on the
left. Repeat for right channel. You can increase
stereo separation by moving the cabinets further
apart. This method is recommended when both
cabinets are on the floor. This method puts a 4
ohm load on each channel. The remaining two
jacks on amplifier should not be used.
Use the
method described for connecting one “WAV
412” cabinet for both cabinets. This is best
when stacking the cabinets on top of each
other because it maintains Left and Right
channel separation inside both cabinets in the
stack. This method uses all 4 speaker jacks
and requires 4 speaker cables. The amp load is
4 ohms per channel so no additional speakers
should be used.
Because this is a stereo amp, you will need to
connect mono cabinets in pairs.
Plug Footswitch into this connector using the
supplied cable. If the cable is lost or damaged, a
standard CAT 5 cable can be used. CAT 5 cables
can be purchased at your local retail electronic
and computer stores.
These ¼” mono jacks deliver the signal going to
the speakers at an unbalanced line level. The main
purpose of these jacks is to deliver line level
outputs to external sound reinforcement devices
such as powered monitors or speakers. They will
not drive external non-powered speakers. To
prevent an undesirable feedback oscillation, do
not use these jacks on signal processors or effects
that will be using the Power Amp Input jacks.
These ¼” mono jacks deliver an unbalanced line
level output from the preamp and digital effects.
The main purpose of these jacks is to send a
signal to the input of third-party signal processors
or effects that will be using the
jacks. These jacks do not interrupt signal flow
from the preamp to the power amp.
These ¼” mono jacks allow the left and right
power amplifiers to be used with an external line
level input. The main purpose of these jacks is to
receive the return signal from a third-party signal
processor or effect. NOTE: When used, these
jacks will interrupt the signal flow from the
preamp to the power amp.
FUSE:
Never
One “WAV 412”cabinet-
Two “WAV 412”cabinets, wide separation-
Two “WAV 412”cabinets stacked-
When used with third-party mono cabinets-
!
!
!
!
®
®
®
®
®
NEVER sum
the left and right channels into a single Mono
cabinet. You can use up to four 16 ohm pairs,
two 8 ohm pairs, or one 4 ohm pair of cabinets.
The total load should not be less than 4 ohms
per channel.
Power Amp Input
8
Rear Panel