Document Outline

• About This Guide
  • Using This Guide
  • About Other Publications
  • Software Included with the Printer
  • Getting Help from Kodak
• 1 Introduction
  • Product Description
    • SCSI Interface
    • KODAK PROFESSIONAL LED II Printer 20P
    • KODAK PROFESSIONAL LED II Processor
    • Installation and Service
  • Equipment Overview
• 2 Using the System
  • Starting up the Processor
  • Starting up the Printer
  • Calibrating the Printer
    • Obtaining Densities
      • Obtaining Densities from a File
      • Using the Densitometer to Read Densities
    • Completing the Calibration
  • Making Prints
  • Shutting Down the Processor
  • Shutting Down the Printer
• 3 System Operating Procedures
  • Operating the Printer
    • Operator Control Panel
      • OCP Key/Light Descriptions
      • Menu
      • Printer Offline Feature
      • Cancelling Jobs
    • Printing Deferred or Buffered Jobs
    • Status Messages
    • Loading Paper Into the Supply Cassette
      • Removing the Supply Cassette
      • Loading Paper into the Supply Cassette
      • Installing the Supply Cassette
    • Reaching the End of the Roll of Paper
    • Removing the Chad
    • Handling and Storing the Paper
      • Storing Paper Using the Soft Shutdown Feature
  • Accessing the Printer Features
    • Shutdown and Restart
      • Shutdown
      • Restart
    • Unload Supply
    • Selecting SCSI Ports
      • Selecting the Target Pad Read Options
    • Managing a Modem
      • Resetting the Modem Port
      • Checking for a Modem
    • Setting the Printer Time and Date
      • Setting the Current Time
      • Setting the Current Date
      • Setting the Current Day
    • Setting the Paper Length
    • Selecting the Slug Width for the Paper
    • Setting the Page Starts Value
      • Producing Borderless Prints
    • Accessing the Software Version Number
    • Setting the Copyright Detection Feature
    • Resetting the Defaults
      • Resetting the Parameters
      • Resetting the Printing LUTs
      • Resetting the Copyright Detection LUTs
    • Changing the Units of Measurement for Paper Sizes
  • About Printing
    • Image Size
    • Buffered and Unbuffered Jobs (or Immediate and Deferred)
      • Printing Deferred or Buffered Jobs
    • Host Software Functions Supported by the Printer
      • Bar Coding
      • Pixel Doubling
  • Operating the Processor
    • Operator Control Panel
      • View Mode
      • Set Mode
      • Calibrate Mode
      • Min Max Mode
      • OCP Key/Light Descriptions
      • Status Messages
      • OCP On/Off Light
    • Operational Modes
      • Adjusting the Key Switch Lock
    • Processing a Control Strip
    • Viewing/Setting the Processor Time and Date
      • Viewing the Current Time Setting
      • Setting the Current Time
      • Setting the Current Date
    • Viewing/Setting the Seven-Day Timer
      • Viewing the On/Off Times
      • Setting the On/Off Times
    • Viewing the Software Identification
    • Viewing/Setting the Temperatures
      • Viewing the Temperature Settings
      • Setting the Temperature
    • Calibrating the Temperatures
    • Resetting the Min Max Temperatures
    • Viewing/Setting Replenishment Settings
      • Viewing the Replenishment Rate
      • Setting the Chemical Replenishment Rate
      • Setting the Wash Replenishment Rate
    • Calibrating the Replenishment Flow Rate
      • Measuring the Flow Rate
      • Entering the Flow Rate
    • Managing the Development Time
      • Viewing the Development Time
      • Setting the Development Time
      • Calibrating the Development Time
      • Displaying the Min Max Development Time
    • Managing the Material Sensors
      • Viewing the Material
      • Viewing the Processor Setup
      • Selecting the Processor Setup
    • Controlling the Processor Drive
      • Turning the Drive On
      • Returning the Drive to Normal Operation
    • Computer Reset
      • Resetting the Processor
      • Loading the Defaults and Changing the Configuration
    • Changing the Wash/Stabilizer Setup
    • Changing the Metric/Fahrenheit Mode
    • Setting the Development Time Tolerance
    • Setting the Chemical Temperature Tolerance
    • Clearing Error Conditions
• 4 Maintaining the Equipment
  • Maintaining the Printer
    • Daily Maintenance
      • Removing the Chad
      • Calibrating the Printer
    • Periodic Maintenance
      • Replacing the Air Filter
  • Maintaining the Processor
    • Daily Maintenance
      • Chemistry Levels
      • Replenishment and Effluent Chemical Levels
      • Cleaning the Crossover Assemblies
      • Operational Checks
      • Testing
    • Weekly Maintenance
      • Checking the Tension of the Main Drive Chain
      • Checking the Circulation
      • Preventing Algae (for Wash Configuration)
      • Cleaning the Crossover Assemblies and Transport Racks
      • Cleaning the Feed Table and the Processor Entrance Sensors
      • Replacing Chemical and Wash Filters
      • Checking the Fittings for Leaks
    • Monthly Maintenance
      • Main Drive Chain
      • Checking the Temperature of the Solutions
      • Checking and Adjusting the Speed of the Processor
      • Cleaning the Tank and Dryer Cover
    • Periodic Maintenance
      • Cleaning Chemical Residue Buildup
      • Cleaning the Processor Tanks
      • Adding New Chemistry
    • Recommended Processor Settings
• 5 Diagnostics and Troubleshooting
  • Printer Error Messages
    • Manual or Automatic Reinitialization
    • Printer Paper Path
    • Printer Error Messages
    • Miscellaneous Printer Error Messages
    • Clearing Printer Paper Jams
    • Troubleshooting Observable Errors
    • Additional Troubleshooting Tips for the Printer
  • Processor Error Messages
    • Clearing Error Messages
    • Clearing a Reset Message
    • Clearing Processor Paper Jams
    • Clearing Drive Errors
    • Additional Troubleshooting Tips for the Processor
  • Calibration Troubleshooting
    • Calibration Graph
    • Calibration Error Codes
    • Non-Numeric Error Messages
  • Getting Additional Help
• Appendix A: Ordering Supplies
  • Accessories
  • Supplies
  • Standard (U.S.) Paper
  • Metric Paper
  • Processor Chemicals
  • Publications
• Appendix B: Specifications
  • Printer/Processor Specifications
    • Dimensions and Weight
    • Acoustic Specifications
  • Site Requirements
    • Operator and Service Access
    • Floor Requirements
    • Plumbing
    • Electrical
    • Power Cords
    • Power Outlets
    • Line Frequency
    • Power Receptacles (U.S. and Canada)
    • Printer Power Receptacles (Europe)
    • Processor Power Receptacles (Europe)
    • Line Voltage
    • Operating Environment
      • Venting the Processor
    • Processor Humidity Specifications
    • Wash Chemicals
    • Telephone line
    • Densitometer
    • SCSI Cable
• Appendix C: Additional Calibration Information
  • Installing the Calibration Software
    • System Requirements
    • Installation Procedure
  • Kodak Device Calibration Software
    • Application Window Definitions
    • Starting the Kodak Device Calibration Software
    • Adding a Device
    • Editing the Log Settings
    • Updating a Device
    • Deleting a Device
  • Advanced Features of the LED II Calibration Software
    • Viewing Graphs
    • Sending LUTs
    • Sending Targets
    • Editing the Calibration Configuration
      • Editing Information on the Procedure Tab
      • Editing Information on the Density Source Tab
      • Editing Information on the Aim Tab
      • Editing Information on the History Tab
      • Editing Information on the Paper Tab
      • Editing Information on the DP2 (Windows NT) or KPIS (Macintosh) Tab
      • Completing the Edit Configuration
    • Creating a Density File for Use with Calibration
    • File Formats
  • Installing the Densitometer
• Appendix D: Using the Image Print Server Software
  • Installing the IPS Software
    • Hardware Requirements
    • Software Requirements
    • Installing the Software
  • Using the Image Print Server
    • Inserting Images into the Print Queue
      • Source Directory Insertion
      • Menu Bar Insertion
    • Suspending and Resuming
    • Failed Jobs
    • Attended Operation
    • Enqueue Example
  • Dialog Boxes and Print Options
    • Option Descriptions
    • Enqueue Dialog Box
      • Option Descriptions
    • Source Directory Preferences Dialog Box
      • Option Descriptions
    • Initialize Default Parameters Dialog Box
      • Description
    • File Format Details
    • Supported Tags
    • LZW Compression
• Appendix E: Using the PHOTOSHOP Export Module
  • Installing the Export Module
    • Hardware Requirements
    • Software Requirements
    • Installing the Software
  • Printing Images
  • Dialog Boxes and Print Options
    • KODAK LED Main Dialog Box
      • Option Descriptions
      • Other options
    • Punch Attributes
      • Option Descriptions
    • Page Layout Attributes
      • Option Descriptions
    • Select an LED Printer Dialog Box
    • Option Descriptions
    • Printer Status Dialog Box
    • Option Descriptions
  • Troubleshooting
    • Error messages
      • General error messages
      • Other Problems