KORG TRITON STUDIO V2 - Manual (Page 20)

15
Sequencer
0–7: Sampling/HD Audio
The 0–7: Sampling page has changed to the 0–7: Sampling/
HD Audio page (the tab has changed from Sampling to
Sampling/HD Audio), and audio track playback parameters
and page menu commands have been added.
0–7a: Input (COMBI, PROG, SEQ, S.PLAY, DISK)
Here you can select input sources such as analog/digital
audio devices and instruments, and set the input level, pan,
bus, and master effect send. (
☞PG p.139 “Global 0–3a: Input
(COMBI, PROG, SEQ, S.PLAY, DISK)”)
0–7b: Ctrl (Control)
A “Ctrl” parameter has been added above “Recording Level
[dB]” (0–7c
☞PG p.56). “Ctrl” lets you choose whether to
adjust the settings for sampling setup or for audio track out-
put. The screen display will depend on the parameter you
select.
Ctrl (Control) [Sampling Setup, Audio Track]
Selects which parameters will be accessible.
Sampling Setup:
Sampling setup parameters. This is the
same as on previous versions. (0–7b ☞PG p.56)
Audio Track: Output settings for the audio tracks.
Pan [L000...C064...R127]
Specifies the panning of the audio track output.
Level [0...127]
Specifies the output level of the audio track.
BUS (IFX/Indiv.) Select [L/R, IFX1...5, 1...4,
1/2, 3/4, Off]
Selects the bus for the audio track.
L/R:
The output of the audio track will be sent to the OUT-
PUT MAIN L (MONO)/R jacks.
IFX1...IFX5:
The output of the audio track will be sent to an
insert effect. To specify the output routing from the insert
effect, use Sequencer P8: Insert Effect, Insert FX page “BUS
Sel. (BUS Select)”
( ☞PG p.84).
1...4: The output of the audio track will be sent to the OUT-
PUT (INDIVIDUAL) 1...4 jack.
1/2, 3/4:
The output of the audio track will be sent to the
OUTPUT (INDIVIDUAL) 1/2 jacks or 3/4 jacks.
Off:
The output of the audio track will not be sent to a bus.
Use this setting if you want to send the audio track output
only to a master effect. To adjust the send level to the master
effect, use “S1 (Send 1 to MFX1)” or “S2 (Send 2 to MFX2).”
S1 (Send 1 to MFX1), S2 (Send 2 to MFX2) [000...127]
Adjusts the send level from the audio track output to each of
the master effects. These settings can be used only if “BUS
(IFX/Indiv.) Select”
is set to L/R or Off. If “BUS (IFX/Indiv.)
Select” is set to IFX1–5, you can adjust the send level to the
master effects by using “Send 1” and “Send 2” that follow
IFX1–5 (8–1b
☞PG p.84).
PLAY/MUTE/REC [PLAY, MUTE, REC, P/R]
This display lets you set the record and play back status of
each audio track.
This setting will change each time you press the PLAY/
MUTE/REC button.
The status of each track may be set independently.
PLAY:
The track will play back.
MUTE: The track will be muted.
REC: This will be displayed when you record. It cannot be
selected.
P/R:
This will be displayed when you perform bounce-
recording ( ☞p.12, 18). It cannot be selected.
SOLO ON/OFF [Off, On]
Switches the solo function on/off.
Only tracks whose SOLO is ON will play back. Other tracks
(including MIDI tracks) will be muted.
The setting will alternate each time you press the SOLO
ON/OFF button.
If the page menu command “Solo Selected Track” (0–
1B) is on, that solo setting will take priority. If you press
“SOLO ON/OFF” or a parameter of another track, only
that track will be soloed and will play back.
The “Pan,” “Level,” “S1,” and “S2” parameters of
Audio Tracks 1 and 2 cannot be controlled by transmit-
ting/receiving or recording MIDI control change mes-
sages. However these parameters can be controlled by
recording/playing exclusive events. (
☞p.34)
0–7c: Recording Level [dB]
This adjusts the signal level at the final stage of recording.
(
☞PG p.92 “Sampling 0–1d: Recording Level [dB]”)
0–7
0–7a
0–7c 0–7b
3
2
2 “Level”
5
5 “PLAY/MUTE/REC”
3 “BUS(IFX/Indiv.) Select”
1 1 “Pan”
4
4 “S1, S2”
6
6 “SOLO ON/OFF ”