Kenwood KRF-V8060D - Manual (Page 22)

22 EN
4 Repeat steps 3 to input the distance for each of the speakers.
5 Press the SETUP key again to return to main setup displays.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
6
Select the display mode.
1 Press the M M M M M/? ? ? ? ? key or Joystick ( 2/3) to select the DISP MODE.
2 Press the SETUP key for the following displays:
1 DISP SELECTOR : Displays the current input selector.
2 DISP LISTEN : Displays the current listen mode.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the display mode.
SL S SB SR
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
LFE
L C R SW
4 Press the SETUP key again to accept the setting.
5 Use the M M M M M key or Joystick ( 3) to select EXIT.
L C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
SL S SB SR
6 Press the SETUP key to exit the SET UP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEM
ACTIV
DSP M
A B CLIP
AUTO DETECT
SW
LFE
CLIP CLIP
1 Use the Input Selector keys to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND and M M M M M/? ? ? ? ? keys or Joystick ( 2/3) repeatedly
until the “INPUT” indication appears.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the
input level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
• The adjustment mode is displayed for approximately 8 seconds.
• The input level may be adjusted to any one of three settings:
0dB, -3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
Preparing for surround sound
Preparing for playback
Some preparatory steps are needed before starting playback.
INPUT MODE
MD/TAPE POWER ON/OFF
(KRF-V8060D)
A SPEAKERS B
POWER
ON/STANDBY
(VR-6060)
ON/STANDBY
(KRF-V8060D)
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing the POWER
ON/STANDBY key (for VR-6060) or POWER ON/OFF and
ON/STANDBY (for KRF-V8060D) key.
Selecting the input mode
If you have selected a component connected to the CD/DVD, VIDEO 2,
VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting is
correct for the type of audio signal to be used.
8
Selecting MD/TAPE
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting is “TAPE”. To
change the source to “MD”, follow the steps below:
Hold down the MD/TAPE key for more than 2 seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat the above procedure.
Selecting the speaker system
Press the A SPEAKERS B key to select the speaker system to be
used.
A ON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
B ON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel. No sound will be heard from
the subwoofer.
A+B ON : Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when
listening with headphones for stereo sound in all playback
modes. The display segments are different depending on
the type of input signal.
The indicator for the speakers
you want to use should be lit.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEM
ACTIV
DSP M
A B CLIP
AUTO DETECT
SW
LFE
• Selecting “6CH INPUT” by pressing the INPUT MODE key, whereby
“DVD/6CH” is the input source will cause SPEAKERS A to be selected
automatically.
Normal playback
•VR6060/21-28/EN 3/11/02, 8:51 PM 22