LG DLEX7177RM - Manual (Page 16)

H O W TO U S E H O W TO U S E
SPECIAL FUNCTIONS
The option buttons also activate special
functions, including DAMP DRY BEEP, CHILD
LOCK, and RACK DRY. Press and hold the option
button marked with the special function
for 3 seconds to activate.
* DAMP DRY BEEP
With this option, the dryer
will beep when the load is
approximately 80% dry. This
allows you to remove faster-drying lightweight
items or items that you would like to iron or
hang while still slightly damp. Press and hold
the ANTI BACTERIAL button for 3 seconds to
activate or deactivate DAMP DRY BEEP.
* CHILD LOCk
Use this option to prevent
unwanted use of the dryer or to
keep cycle settings from being
changed while the dryer is operating. Press and
hold the EASY IRON button for 3 seconds to
activate or deactivate the CHILD LOCK function.
The lock icon will be shown in the display, and all
controls are disabled.
EASY IRON
* CHILD LOCK
MAX
CUSTOM PROGRAM
If you have a special combination of settings
that you use frequently, you can save these
settings as a CUSTOM PROGRAM.
* To Save a Custom Program:
Turn on the dryer and turn the cycle selector
knob to select the desired cycle.
Use the cycle setting buttons to adjust the
settings for that cycle.
Press the cycle option button(s) for the option
you would like to add. A confirmation message
will be shown in the display.
Press and hold the CUSTOM PROGRAM button
for 3 seconds.
1
2
3
4
To Recall a Custom Program:
Turn on the dryer.
Press the CUSTOM PROGRAM button.
Press the START/PAUSE button to start
the cycle.
1
2
3
Water
ONLY
w
WARNING:
• Do not fill the steam feeder with liquids such as gasoline, dry-cleaning solvents, or other flammable
or explosive substances. They give off vapors that could explode.
• Do not fill the steam feeder with hot water (over 86° F / 30° C).
• Do not drink water from the steam feeder.
NOTE: You may only save one custom
program at a time. Pressing and holding the
CUSTOM PROGRAM button will overwrite
any previously saved custom program.
BEFORE USING THE STEAM FUNCTIONS
1
2
3
4
To Fill the Steam Feeder
Pull out the drawer.
Lift out the steam feeder.
Fill the steam feeder to MAX with water.
Place the steam feeder in the drawer, then
push in the drawer until it clicks into place.
IMPORTANT NOTES ABOUT STEAM CYCLES
• Only use water. Do not fill the steam feeder with foreign substances, rinse agents, or detergents.
• Before using a Steam Cycle, the steam feeder must be filled with water up to the MAX line. If not, the
ADD WATER light will blink. Make sure that the steam feeder is filled with water or the drawer is fully
closed. Turn the dryer off then restart the Steam Cycle.
• Before moving the dryer, make sure the steam feeder is empty.
• Do not use distilled water; the water level sensor in the steam generator will not work.
• Be careful to put the Steam Feeder otherwise water will be overflow.
• Wipe up any spilled water around the Steam Feeder and the drawer before starting the dryer.
Steam
Feeder
Drawer
0 1
* RACk DRY
Use RACK DRY with items,
such as wool sweaters, silk, and
lingerie, that should dry flat. RACK
DRY can also be used with items that should not
be tumbled dry, such as gym shoes or stuffed
animals. Press and hold the WRINKLE CARE
button for 3 seconds to activate or deactivate the
RACK DRY function.
NOTE: NEVER use the rack with a tumble
dry cycle.
To Install the Drying Rack
With the dryer door open, slide the rack into
the dryer drum.
1
Make sure it is seated evenly on the edge
of the inner door rim and resting flat on the
inside of the dryer.
NOTE: Be sure to remove the drying rack
after using the RACK DRY cycle.
2