Life Fitness 95T - Manual (Page 4)

IMPORTANT !
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS
LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION.
IMPORTANT !
CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE-
SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES.
1. Remove the six SCREWS (A) securing the MOTOR COVER (B). Lift
and remove the MOTOR COVER and set it and the SCREWS
aside.
2. Locate the LEFT UPRIGHT (1). With the notched end facing upward
and closest to the treadmill, lay the LEFT UPRIGHT near the LEFT
UPRIGHT MOUNTING BRACKET (C) as shown.
3. Feed the CONSOLE CABLE (D) through the front channel (toward
motor compartment) of the LEFT UPRIGHT (1).
Feed the ENTERTAINMENT POWER CABLE (E) through the cen-
ter channel of the LEFT UPRIGHT (1).
Tilt the LEFT UPRIGHT upward and carefully insert it onto the
LEFT UPRIGHT MOUNTING BRACKET. Secure the LEFT
UPRIGHT using three BOLTS (2) and WASHERS (3). Leave the
BOLTS loose at this time.
NOTE: BE CAREFUL NOT TO PINCH THE
CABLES WHEN INSERTING THE LEFT
UPRIGHT ONTO THE LEFT UPRIGHT
MOUNTING BRACKET.
4. Locate the RIGHT UPRIGHT (4). With the
notched end facing upward and closest to the tread-
mill, lay the RIGHT UPRIGHT near the RIGHT UPRIGHT
MOUNTING BRACKET (F) as shown.
5. Feed the C-SAFE (G) and COAXIAL CABLES (H) through the front
channel (toward motor compartment) of the RIGHT UPRIGHT (4).
Tilt the RIGHT UPRIGHT upward and carefully insert it onto the
RIGHT UPRIGHT MOUNTING BRACKET. Secure the RIGHT
UPRIGHT using three BOLTS (2) and WASHERS (3). Leave the
BOLTS loose at this time.
NOTE: BE CAREFUL NOT TO PINCH THE CABLES WHEN
INSERTING THE RIGHT UPRIGHT ONTO THE RIGHT
UPRIGHT MOUNTING BRACKET.
6. Carefully insert the HANDRAIL/BRIDGE ASSEMBLY (5) into the
top of the RIGHT and LEFT UPRIGHTS (1 & 4). Secure the
HANDRAIL/BRIDGE ASSEMBLY using six BOLTS (2) and WASH-
ERS (3). Tighten the BOLTS securely.
NOTE: CAREFULLY PULL BACK THE HANDRAIL SHROUDS TO
INSTALL THE BOLTS FROM THE FRONT. DO NOT PULL THE
SHROUDS FURTHER THAN IS NEEDED TO INSTALL THE
FRONT BOLTS.
NOTE: BE CAREFUL NOT TO DAMAGE ANY CABLES WHEN
INSTALLING THE CONSOLE BRIDGE. LEAVE CABLES LOOSE
AT THIS TIME.
7. Attach the CONSOLE BRACKET (6) to the HANDRAIL/BRIDGE
ASSEMBLY (5) as shown using eight SCREWS (7) and WASH-
ERS (8). Start all eight screws but leave them loose at this time.
While standing on the treadmill, pull the top of the CONSOLE
BRACKET toward the user pushing the front edge downward.
Tighten the four front SCREWS securely. Tighten the remaining
four back SCREWS securely.
4
1
3
3
F
B
A
1
2
3
2
3
2
D
E
H
G
D
E
C
3
2
3
4
3
2
3 2
3
5
1
2
3
2
5
7
8
6
8
7