Land Pride RCM6015 - Manual (Page 41)

39
Section 7: Features and Benefits
8/28/08 RC5015 & RC6015 (540 RPM) and RCM5015 & RCM6015 (1000 RPM) Rotary Cutters 318-047M
Land Pride
Table of Contents
318-047
RC5015 & RCM5015 Rotary Cutters
Features Benefits
250 HP Splitter box Highest gearbox rating in its class.
210 HP wing boxes Highest gearbox rating in its class.
Tractor HP range 50 - 250 HP
Left wing counter rotates Better discharge of material.
Factory assembled Saves the customer set up time.
Gearbox warranty S/N 325492+ 5 years on housing, gears and shafts, 3 years on seals & bearings.
S/N 325491- 1 year warranty.
2 3/8” Gearbox output shaft Large output shaft handles shock loads better.
Star profile drivelines Increased strength in driveline. Holds up to shock loads and harsh mowing conditions.
Input driveline: Cat. 5 Constant velocity or conventional u-joint available.
540 or 1000 RPM Fits wide variety of tractors.
Self-leveling clevis type hitch Reduces drawbar wear by keeping hitch level while going through ditches.
Gearbox seal protection Gearbox bottom seal is protected for longer bearing life.
3/16” Deck thickness Heavy gauge material aids in resisting damage from debris hitting the underside of the deck.
1/4 ” Sidewall thickness Reduces debris piercing possibilities.
10 1/2 ” Deck height Handles heavy cutting, which reduces balling up of cut material under the deck.
2” to 14” Cutting Height Cover a wide range of cutting conditions.
6” Blade overlap Eliminates skipping during turns.
4” Cutting capacity Enables the cutter to be used in pastures with small trees up to 4” in diameter.
High blade tip speed (540 rpm = 15,268 fpm center & 15,000 fpm wings)
(1000 rpm = 15,578 fpm center & 14,620 fpm wings)
Allows clean cutting of material.
Replaceable skid shoes Can be replaced when damaged or worn out on wings and center deck.
3/16” Round stump jumper
with 1” thick plate 1” Thick plate offers superior support and protection to gearbox output shaft.
Deck rings (option) Helps keep the blades from getting into and damaging the deck.
4 Plate slip-clutch Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
Easy to Grease drivelines Drivelines have access holes to grease the U-joints of the driveline, as well as holes to
grease the inner profiles.
Hinged wing sections Allow you to shape the cutter to the job. Ideal for rough ground where hillsides, ditches and
hollows can cause uneven cutting.
1” Solid hinge rods L arger diameter hinge rod gives greater strength to the cutter from front to rear, and in the
hinge area itself.
Wing transport locks Transport wing locks securely hold wings in the folded position in case of hydraulic failure.
Enclosed front to rear dual
leveling rods Dual leveling rods enable the cutter to pull equally on the rear axle during uneven terrain
vs. just pulling from one side of the front hitch.
Airplane tire option
with optional foam sealant Airplane tires give better cushion while transporting the cutter. Available with heavy-duty
foam which virtually eliminates flats.
Laminated tires option Can’t go flat.
Replaceable wheel spindles Wheel spindles can be replaced easily by removing two bolts vs. replacing the entire axle.
Wheels 6 or 8 Wheel option.
Spring cushioned center-axle Protects unit from bumps and ground shock.
Walking Tandem Axles
(Option) Better flotation over rough terrain.
Surpassed rugged industry
standards All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing
procedures specified by ANSI.
Paint options Choice of red, green or tan to match popular tractor lines.