Before operation-vcr part, Tuning in a video channel on your tv, Using your vcr for the very first initial preset – LG LH-CX245 User Manual

Page 17: Installation and setup, Channel built into it, usually called av, Scart

Advertising
background image

Installation and Setup

Before Operation-VCR part

Tuning in a video channel on your TV

Notes

• The output frequency of this video recorder (VCR) is

set at UHF channel 60. If channel 60 is already
used by another TV station, or if the picture is
distorted, you can change the transmitter channel of
your DVD/VCR Combi receiver. Stages 5 ~ 8 will
show you how to change the output frequency of
your DVD/VCR Combi receiver.

• Your TV receives signals from the video recorder

(VCR) like another TV station. You have to select a
channel number on your TV and tune it in so that
you may watch video tapes. If you have used a
SCART cable then your TV should already have a
dedicated video

channel built into it, usually

called AV.

1. Make sure that you have correctly installed your

VCR as described earlier in this book.
Press POWER to turn on your DVD/VCR Combi
receiver. Turn on your TV.

2. Insert a pre-recorded video tape into your

DVD/VCR Combi receiver and press PLAY on the
remote control. Select a TV channel number on
which you wish to watch video’s.
Don’t worry if you don’t have a video-tape to play
at this stage! If you switch your DVD/VCR Combi
receiver on and continue stages 3 ~ 4, instead of
seeing video playback tune your TV until you see
a bright blue screen.

3. Tune this channel until the video picture is sharp

and the sound is clear.
If you have used a

SCART

cable you will not

have to tune your TV, simply select the AV
channel. The AV channel is already pre-tuned for
optimum video playback on your TV.

4. Store this channel on your TV.

You will need to look at the TV instruction book if
you do not know how to do this.

5. Only carry out stages 5 ~ 8 if you cannot

obtain clear video playback as described in
stages 1 ~ 4.
Select a TV channel number on
which you wish to watch video’s.
Make sure that your DVD/VCR Combi receiver is
in standby pressing POWER on the remote control
(only the clock will be displayed).

6. Press PROG.

+ or -

on the front of your DVD/ VCR

Combi receiver for more than 4 seconds.
RF60 will appear in the display window.
The following picture will be displayed on the TV
screen.

7. Press PROG.

+ or -

to select another video channel.

You may select any channel number between 22
and 68.
You can also set it to “OFF” if there is any interfer-
ence when your TV is connected to the DVD/VCR
Combi receiver with a SCART lead.

8. Select a TV channel number on which you wish to

watch video’s. Press

STANDBY/ON on the front

of your DVD/VCR Combi receiver when you have
finished. Tune this channel so that a bright blue
screen appears. Store this channel on your TV.

Notes

Make sure that you have correctly installed your
DVD/VCR Combi receiver and successfully tuned in a
dedicated video channel on your TV. If you do not
tune in a dedicated video channel on your TV you will
be unable to view and record video tapes!

Using your VCR for the very first
Initial preset

For the following steps we do assume that you have

just connected your video recorder for the very first

time. In this case the video recorder is on after mains

connection. You should not touch any buttons yet. On

the connected TV you will now see.

Note - If this menu does not appear, your video

recorder was programmed already.

1. Select the country according to your area with

F

and

G

.

“A”: Austria, “B”: Belgium, “CH”: Switzerland, “D”:

Germany, “DK”: Denmark, “E”: Spain, “F”: France,

“I”: Italy, “N”: Norway, “NL”: Netherlands, “P”:

Portugal, “S”: Sweden, “SF”: Finland, OTHERS.

2. Press OK to start the automatic storing of the

channels of the TV stations in your area.

i

RF CHANNEL 60

PSET

R

17

A
N

NL

P

S

SF

B

D DK

E

F

I

OK

i

Pr-12

ACMS

CH

OTHERS

Pr-12

ACMS

01

C02

00 PR-01

E

S

i

Advertising