Land Pride RCM5015 - Manual (Page 20)

Revision Comments Part Description Part No. Ref.
HHCS 3/4-10X2 GR5 802-064C 9.
Rev. 2 not compat. w/Rev. 1. (S/N 325492+) SHIELD WELDMENT 318-400H 10.
Rev. 1 (S/N 325491-) SHIELD WELDMENT 312-399H 10.
WASHER FLAT 3/8 SAE PLT 804-012C 11.
KNOB 3/8-16 FEMALE THD 2 3/8OD 817-259C 12.
NUT WING 3/8-16 PLT 803-231C 12.
WASHER LOCK SPRING 3/8 PLT 804-013C 13.
Rev. 2 not compat. w/Rev. 1. (S/N 325492+) SHIELD BRACKET WELDMENT 318-401H 14.
Rev. 1 (S/N 325491-) SHIELD MOUNT BRACKET WELDMENT 312-400H 14.
WASHER FLAT 5/16 USS PLT 804-010C 15.
WASHER LOCK SPRING 5/16 PLT 804-009C 16.
HHCS 5/16-18X3/4 GR5 802-007C 17.
BLADE BOLT ACCESS COVER 312-812D 18.
BLADE BOLT ACCESS COVER GREEN 312-812D81 18.
BLADE BOLT ACCESS COVER RED 312-812D83 18.
NUT HEX WHIZ 3/8-16 PLT 803-198C 19.
PLOW 3/8-16X1 1/4 GR5 802-466C 20.
Rev. 2 not compat. w/Rev. 1. (S/N 292792+) SKID SHOE 318-335D 21.
Rev. 1 (S/N 292791-) SKID SHOE 318-096D 21.
RC5015 & RC6015 804-169C OMNI
WASHER HARDENED 1 1/8 USS COMER BLANK WASHER 0.288.7101.00 22.
RC5015 & RC6015 COMER CASTLE NUT M36X3 8.2.2.00560 23.
RC5015 OMNI NUT HEX SLOTTED, 1 1/4 120092 23.
RC6015 OMNI NUT-HEX SLOTTED, 1 1/4-18 120095 23.
PIN COTTER 1/4 X 2 1/2 PLT 805-105C 24.
(S/N 219146+) Shown DEFLECTOR FLAT LH. 318-171D 25.
DEFLECTOR FLAT LH. GREEN 318-171D81 25.
DEFLECTOR FLAT LH. RED 318-171D83 25.
(S/N 219146+) DEFLECTOR FLAT RH. 318-170D 25.
DEFLECTOR FLAT RH. GREEN 318-170D81 25.
DEFLECTOR FLAT RH. RED 318-170D83 25.
RC5015 PTO CAT.4 W/CLUTCH 1 3/4-20 826-185C 26.
Rev. 2 RC6015 (S/N 461635 to 461937,
468573+) PTO V80 X 59.3 1280NM CLUTCH 826-481C 26.
Rev. 1 RC6015 (S/N 461634-) RPBY 826-481C 826-262C 26.
* *
* *
Note "A": When replacing this gearbox dishpan
modification required. Contact Service
Department. *
Note B: Can use dishpan (318-012H) w/ this
replacement gearbox *
20 RC5015, RCM5015, RC6015 & RCM6015 Rotary Cutters 318-047P 12/31/12
Table of Contents Part Number Index
Land Pride Section 2: Decks
RC5015 & RC6015 SERIES (540 RPM)
Deck Wing Section (540 RPM) (continued)
Applies to RC5015, RC6015