Lightolier 2000LVR - Manual (Page 2)

5. SNAP-ON (Fig. E)
6. PUSH-UP (Fig. F)
7. LAMPING (Fig. L)
1. Make sure that power is OFF when lamping or relamping.
Remove LAMP RING from SOCKET CUP by pulling straight down.
2. Insert LAMP (MR16 bulb) between LAMP SPRINGS until face of
bulb sits firmly on GLASS LAMP GUARD. (Fig. L)
3. Attach SOCKET to bi-pin prongs on LAMP.
4. Insert LAMP RING with LAMP and GLASS LAMP GUARD back
into SOCKET CUP.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:2000LVR
B0698 Page 2 of 2
4. ATTACH MOUNTING RING (Fig. D)
IMPORTANT: If using TRIMS 2022LV, 2024LV, or 2004 Series,
discard MOUNTING RING and follow Steps in 4A.
Push MOUNTING RING into opening until FLANGE sits against
ceiling. Slide MOUNTING STRAPS down to trap ceiling thickness
and then bend up to secure.
SEE SEPARATE
REFLECTOR TRIM
INSTRUCTION SHEETS.
}
;;
;;
MOUNTING CLIP
MOUNTING RING
FLANGE
8. ADJUSTMENT (Fig. M)
1. For vertical adjustment insert blade of screwdriver into the open
slot of YOKE.
2. Using the screwdriver as a lever, tilt the entire LAMP HOLDER to
the desired angle.
3. For horizontal adjustment, rotate the LAMP HOLDER.
WARNING :
1. LAMP MANUFACTURERS REQUIRE THE GLASS LAMP GUARD BE IN
PLACE BEFORE ENERGIZING LAMP, AND THAT GREAT CARE MUST BE
TAKEN THAT LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID
FINGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT
LAMP LIFE AND POSSIBLE BREAKAGE.
2. USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER, INC. THE
USE OF OTHER MANUFACTURER’S REFLECTOR TRIMS VOIDS THE
UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE
A FIRE HAZARD.
NOTE:
1. LOW VOLTAGE FIXTURES should be dimmed only with special dimmers intended
specifically for that purpose. Use Lightolier Lytemode, Scenist, Crescendo VA,
Neptune VA, Precision VA, Easyset VA, Sunrise VA, Radiant VA or autotrans-
formers or electronic dimmers intended for use with low voltage fixtures.
2. LOW VOLTAGE FIXTURES may produce audible sound when used with dimmers,
which may be objectional in acoustically critical areas.
Fig. K
Fig. L
Fig. M
MALE CONNECTORS
(ATTACHED TO SOCKET WIRES) INSULATED SLEEVING
FEMALE CONNECTORS
(ATTACHED TO FIXTURE WIRES) MR16 SOCKET
SOCKET
LAMP SPRING
LAMP RING
GLASS LAMP
GUARD
LAMP
SOCKET CUP
LAMP HOLDER
APERTURE TRIM
ASSEMBLY
YOKE
4A. PUSH-UP AND CLIP-ON
1. CLIP is inserted from inside
housing, through “T” slot.
2. Downward force is then
applied, with screwdriver
on top of CLIP or engaged
in SCREWDRIVER SLOT in
CLIPS FLANGE.
3. Force is applied until CLIP
is snugly seated.
INSIDE OF
HOUSING
STEP 1
STEP 2
STEP 3
TO INSERT
“T” SLOT IN
HOUSING
SHORT HANDLE
SCREWDRIVER
CEILING
ASSEMBLY