Land Pride RCR2510 - Manual (Page 11)

Revision Comments Part Description Part No. Ref.
Drawing Image Number dwg22333
SHIELD BRACKET WELDMENT 312-765H 1.
RCR2596 DISHPAN WELDMENT 15" CTR 312-767H 2.
RCR(M)2510 DISHPAN WELDMENT 17" CTR 312-748H 2.
Right Hand RCR2596 CW BLADE CARRIER ASSY 312-769S 3.
Right Hand RCR2510 CW BLADE CARRIER ASSY 312-749S 3.
Left Hand RCR2596 CCW BLADE CARRIER ASSY 312-770S 4.
Left Hand RCR2510 CCW BLADE CARRIER ASSY 312-750S 4.
RCR2596 OUTER SHIELD 326-116D 5.
RCR2510 OUTER SHIELD 326-101D 5.
HHCS 1/2-13X1 1/4 GR5 802-034C 6.
(S/N 558465+) HHCS 3/4-10X2 1/4 GR5 802-065C 7.
(S/N 558464-) HHCS 3/4-10X2 GR5 802-064C 7.
BLADE BOL 1 1/8-12X3 7/16 W/KY 802-277C 8.
HHCS M8X1.25X20 GR8.8 802-314C 9.
NUT HEX TOP LOCK 1 1/8-12 PLT. 803-170C 10.
NUT HEX FLG TOP LK 3/4-10 PLT 803-299C 11.
WASHER LOCK SPRING 1/2 PLT 804-015C 12.
WASHER FLAT 1 HARD ASTMF436 PN 804-147C 13.
WASHER SPRING LOCK M8 PLT 804-157C 14.
WASHER FLAT M8 PLT 804-161C 15.
GRBOX SHAFT(1 3/4OD) PROTECTOR 817-165C 16.
KNOB 3/8-16 FEMALE THD 2 3/8OD 817-259C 17.
RCR2596 Standard CUTTER BLADE 1/2X4X20 1/2 CCW 820-195C 18.
RCR2596 Optional CUTTER BLADE 1/2X4X20.5 LL CCW 820-210C 18.
RCR2510 RCRM2510 Standard CUTTER BLADE 1/2 X 4 X 25 CCW 820-137C 18.
RCR2510 RCRM2510 Optional CUTTER BLADE 1/2X4X25 LL CCW 820-193C 18.
RCR2596 Standard CUTTER BLADE 1/2X4X20 1/2 CW 820-196C 19.
RCR2596 Optional CUTTER BLADE 1/2X4X20.5 LL CW 820-211C 19.
RCR2510 RCRM2510 Standard CUTTER BLADE 1/2 X 4 X 25 CW 820-112C 19.
RCR2510 RCRM2510 Optional CUTTER BLADE 1/2X4X25 LL CW 820-209C 19.
RCR2596 PTO STD.W/4-PLATE SC CAT4 540 826-255C 20.
RCR2510 PTO STD.W/4-PLATE SC CAT4 540 826-215C 20.
RCRM2510 PTO STD.W/2-PLATE SC CAT4 1000 826-216C 20.
RCR2596 RCR2510 T-BOX 1.75-20 1:1.35 826-356C 21.
RCRM2510 T-BOX 1.75-20 1.35:1 826-424C 21.
GBOX 1:1.50 STD. 1.38-6 SPL. 826-358C 22.
RCR2596 FLEX CPLR 1.75-20 TO 1.38-6 S 826-360C 23.
RCR2510 RCRM2510 FLEX CPLR 1.75-20 TO 1.38-6 826-359C 23.
As Required BLADE SPACER 16 GA .06 thick 312-075D 24.
As Required BLADE SPACER 18 GA .05 thick 312-082D 24.
As Required BLADE SPACER 20 GA. .04 thick 312-089D 24.
As Required BLADE SPACER 24GA .03 thick 312-808D 24.
GREASE ZERK STRAIGHT 1/4-28 800-001C 25.
COMER VENT #8.6.7.00269 826-497C 26.
BLADE BOLT KIT 318-586A 27.
01/04/13 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 11
Table of Contents Part Number Index
Section 2: Frame Land Pride
Deck Blade Drive S/N 644967-
Applies to RCR2510, RCR2596, RCRM2510