LeapFrog Nitro 4-Tec 3.3TM all-wheel-drive 4809 - Manual (Page 30)

is..
Lower
Higher
Lower
Higher
Lower
Higher
Lower
Higher
Lower
Higher
then the air density is...
Slightly more dense
Slightly less dense
Less dense
More dense
More dense
Less dense
More dense
Less dense
adjust (correct) the
fuel mixture to be...
Slightly richer
Slightly leaner
Leaner
Richer
Richer
Leaner
Richer
Leaner
Leaner
Richer
If the...
Humidity
Pressure (barometer)
Temperature
Altitude
Nitro %
Fuel Mixture Adjustment Chart
30 • Nitro 4-Tec 3.3
Before you begin tuning, the engine should be warmed up to its normal
operating temperature and running slightly rich. All final tuning adjustments
must be made to the engine at its normal operating temperature. You can
tell the engine is running rich by noting any of the following:
Sluggish acceleration with blue smoke coming from the exhaust.
Nitro 4-Tec may not shift into second gear.
There is unburned fuel spraying from the exhaust tip.
Leaning the high-speed fuel mixture increases performance.
High-Speed Fuel Mixture Adjustment
With the engine warm and running at a rich setting, gradually lean the
high-speed fuel mixture in 1/16 turn increments. Make several high-
speed passes after each adjustment to clear out the engine and note any
change in performance. The TRX 3.3 is extremely powerful. Remember to
apply the throttle gradually to prevent spin-outs or loss of control.
Continue this procedure until there is no longer any performance
improvement. If any one of the following conditions occurs, the fuel
mixture is already past the maximum safe lean setting:
1. There is no longer any performance improvement.
2. The engine begins to cut out at high speed (Danger!).
3. There is a sudden loss of power during acceleration (Danger!).
4. The engine begins to overheat. Symptoms of overheating include:
Steam or smoke coming from the engine (not exhaust).
Hesitation or stalling during acceleration.
Popping or clattering sound when decelerating (detonation).
Fluctuating idle speed.
Temperature measurement above 270° F at the glow plug
(A temperature reading above 270° alone does not necessarily
indicate overheating. Look for other symptoms of overheating
combined with temperature for a more accurate warning).
Richen the fuel mixture to the optimum setting by richening the high-
speed needle at least 1/8 turn counterclockwise and retest. This setting
will extend engine component life.
Low-Speed Fuel Mixture Adjustment
The low-speed mixture is always set after the high-speed needle is correctly
adjusted. The low-speed mixture is set using the pinch test.
1. Once the engine is warm, do several high-speed runs to confirm
that the high-speed needle is set correctly.
2. Bring the vehicle in and pinch closed the fuel line going into the
carburetor (use the engine shut-off clamp). The engine should run for 2-3
seconds, speed up, and then shut off.
3. If the engine runs longer than 3 seconds, then lean the low-speed needle
1/16 turn, make several more high-speed runs, and retest.
4. If the engine shuts off immediately without speeding up, then richen the
low-speed needle 1/8 turn, make several more high-speed runs, and retest.
When the low-speed needle is set correctly, the engine’s throttle response
should be very quick, even to the point of making it difficult to keep Nitro 4-
Tec from doing a wheelie when you accelerate!
The TRX 3.3 Racing Engine
When adjusting the low
speed fuel mixture, it is
very important to make
several high-speed runs
with Nitro 4-Tec between
adjustments to clear out
any excess fuel. Perform
the pinch test immediately
after. If the engine is
allowed to idle for a long
period of time, it could
“load up” with fuel and
give you an inaccurate
measurement from your
pinch test.
Higher nitro requires a
richer fuel mixture. When
running 33% fuel, richen
your high speed needle 3/4
turn if previously running
20% nitro and then re-tune
the engine for maximum
performance. See page 21
for more information