Lightolier Architectural Decorative CCLRD01 - Manual (Page 2)

Architectural Decorative
IS:CCLRD01
Page 2 of 3 Instruction Sheet for Assembly and Installation
Lightolier is a Philips group brand
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2008 Philips Group • A0908
Installation
The color rotary dial control shall be installed by a qualified electrician in
accordance with NEC and relevant local codes for power supplies with
Class 2 outputs.
Data
+
Ground Ground +24 VDC Data
-
Mode Selection
ON: Enabled OFF: Disabled
Mounting Holes
WARNING: Ensure that power is off before installing the color rotary dial control.
Enable/Disable
DIP Switches
Fig. 2
Five-position
Terminal Block
Color Rotary Dial Control Back
Data
+
Ground Shield +24 VDC Data
-
Modes:
1. Fixed color
2. Color wash
3. Rainbow (4)
4. Rainbow (8)
5. Rainbow (12)
6. Random
7. Random fade
8. White Mode Selection
ON: Enabled OFF: Disabled
Wiring the color rotary dial control (refer to Fig. 3 wiring diagram)
1. Using the 18 AWG power cable, connect 24 VDC and ground from
power supply to the screw terminal located on the back of the color
rotary dial control.
2. Using the CAT 5 data cable, connect data from the color rotary dial
control power/data supply to the screw terminal located on the back
of the color rotary dial control.
To Disable Effects:
When you receive your color rotary dial control, eight light effects are
preprogrammed and enabled. If you wish to limit the number of effects in
the cycle, or if you know of effects that you will not use, you can disable
the them prior to physically installing the color rotary dial control into the
wall box.
• To disable an effect, set its corresponding dip switch to OFF.
1. Fixed Color
2. Color Wash
3. Chasing Rainbow (4 lights wide)
4. Chasing Rainbow (8 lights wide)
5. Chasing Rainbow (12 lights wide)
6. Random Color
7. Random Fade
8. White
Note: Keep in mind that any effects you disable prior to installation can
only be re-enabled by physically removing the color rotary dial control
from the wall box and turning on the appropriate switch.
Mounting the color rotary dial control:
Now that you have wired the color rotary dial control, and disabled/
enabled the desired effects, you are ready to mount it.
1. Using screws provided, align the mounting holes to a one gang wall
box, or a single area of a multi gang wall box, and attach.
2. Attach face plate.
3. Attach knob by aligning the collar with the rotation shaft and press.
Operating color rotary dial control
Using the color rotary dial control is as simple as pressing and turning.
Press the dial to cycle through the eight effect modes and OFF.
Turn the dial to vary the effects.
In Fixed Color mode, turning the dial changes the color. While in White
mode, turning the dial changes the intensity. In all other modes, turning
the dial adjusts the speed. Color rotary dial control remembers your set-
tings and recalls them each time you return to the effect.
Turn the dial clockwise to increase, and counter-clockwise to decrease,
the speed. The first three revolutions of the dial varies the speed between
approximately 1/2 second to about 2 minutes. After which, each click of
the dial doubles the speed clock-wise or decreases by half counter-clock-
wise. When in this range, the lights snap to a new color with each click
for visual confirmation of changes.
Note: In Chasing Rainbow, the speed of a single pass through the color
spectrum ranges from 1/2 second to 5 hours. After the third rotation of
the dial, the speed is reduced to the point that color changes are not
immediately visible.
The color rotary dial control outputs data for light addresses 1 through 60.
After the first 12 addresses, the data is repeated. For installations with
more than 12 lights you can either sequentially address the lights past 12,
up to 60, or repeat the addresses starting from 1. The effects will appear
the same. Below is an example of light addressing with 24 lights.
1 2 4 11 12 13 14 21 22 23 24
1 2 4 11 12 1 2 9 10 11 12
3
3
. . . . . .
. . . . . .
Sequential Addressing
Repeat Addressing