Rre ea arr p pa an ne ell – Peavey TransTube 100 EFX User Manual
Page 7
((116
6))
R
RE
EM
MO
OT
TE
E S
SW
WIIT
TC
CH
H
This eight-pin DIN connector is provided for connection of the PFC 3 footswitch (included). The
footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH
section of this manual for explanation of footswitch operation.
((117
7))
E
EFFFFE
EC
CT
TS
S LLE
EV
VE
ELL S
SW
WIIT
TC
CH
H
Selects the effects loop operating level: -10 dBV (0.3V RMS) when “out” and 0 dBV (1 V RMS)
when “in”.
((118
8))
E
EFFFFE
EC
CT
TS
S S
SE
EN
ND
D
Output for supplying signals to external low-level effects or signal processing equipment.
((119
9))
E
EFFFFE
EC
CT
TS
S R
RE
ET
TU
UR
RN
N
Input for returning signals from external low-level effects or signal processing equipment.
((2
20
0))
P
PR
RE
EA
AM
MP
P O
OU
UT
T
The preamp out can be used to route the amplified signal from the preamp to a mixing console,
tape recorder, etc. Connect the preamp output to line-level inputs of other equipment using high
quality shielded cable. This patch does not affect operation of the amplifier.
((2
211))
P
PO
OW
WE
ER
R A
AM
MP
P IIN
N
Used to connect line-level signals to the power amplifier section. Connect the power amp input to
line-level output of other equipment using high quality shielded cable. This patch disconnects the
preamp section from the power amp section.
((2
22
2))
D
DA
AM
MP
PIIN
NG
G
This three-position switch allows for adjustment of the damping factor of the power amplifier.
Damping is the ability of an amplifier to control speaker cone motion after the signal disappears.
A higher damping factor (TIGHT) reduces cone vibration more quickly than a lower damping factor
(LOOSE). This switch works much like the Resonance and Presence controls found on other
Peavey amps, if they were to be turned simultaneously. If the Damping switch is changed, the
volume level of the amp will also change and may require re-adjustment of the volume.
((2
23
3))
P
PO
OW
WE
ER
R
This three-position switch selects the power output level of the power amplifier. This switch
works like the T. Dynamics
®
control found on other Peavey amplifiers which provides for a more
pronounced tube power compression simulation at lower settings.
7
R
Re
ea
arr P
Pa
an
ne
ell
Sticker area
Keep out
Serial
REMOTE
SWITCH
120V
60 Hz
300 WATTS
GND.
0
WARNING:
CAUTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
AVIS:
TO RAIN OR MOISTURE.
ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT
TO REDUCE THE RISK OF FIRE OR
TRANSTUBE 100 EFX HD
EFX
LEVEL
EFX
EFX
PRE AMP
OUT
PWR AMP
IN
SEND
RETURN
-10 dBV (.3V RMS)
0 dBV (1V RMS)
LOOSE
POWER
DAMPING
MEDIUM
TIGHT
100W
50W
25W
SPEAKER OUTPUTS
100 WATTS RMS/40V RMS, 4 OHMS MIN.
SPEAKER JACKS PARALLELED
IMPEDANCE SELECTOR
4
16
8
R
16
16
23
25
20
19
17
27
26
22
21
18
24