Panasonic TC 32LX700 - Manual (Page 38)

38 39
Advanced
Recommended
A
V
Connections
1 2
ANT
AV IN
1 2 ANT
AV IN
Recommended AV Connections
These diagrams show our recommendations for how to connect the TV unit to your various equipment.
For other connections, consult the instructions of each piece of equipment and the specifications (p. 49).
For additional assistance, please visit our website at: www.panasonic.com
www.panasonic.ca
AC 110 - 127 V
60Hz
Power Cord
(Connect after all the other
connections are complete.)
Back of the TV
■
To watch
camcorder
images
Camcorder
VCR
DVD Player
M3 plug
Headphones/
Earphones
(not supplied)
•
Individual HDMI equipment may require additional menu settings specific to each model. Please refer to their
respective operating instruction manuals. •
When audio from other equipment connected to this unit via HDMI is output using “DIGITAL AUDIO OUT” of this
unit, the system switches to 2CH audio.
(When connecting to an AV amp via HDMI, you can enjoy higher sound quality.)
Note
HDMI cable
Cable Box
Cable TV
or
■
To watch DVDs
DVD Player/Set Top Box
Optical digital audio cable
•
The picture and audio input signals connected to a
terminal specified in “Monitor out” (p. 34) cannot be
output from “OUTPUT” terminals.
However, audio output can be obtained from
“DIGITAL AUDIO OUT” terminal. •
To prevent howling and image oscillation, set the
“Monitor out” setting when connecting the VCR with
loop-connection. (p. 26, 34)
Note
■
DVD Recorder /
VCR
AUDIO
IN
HDMI
(AV OUT)
HDMI
(AV OUT)
Panasonic RAM theater /
Panasonic Player theater
or
or
HDMI
(AV OUT)
Panasonic AV amp DIGA
(Panasonic DVD
Recorder)
Follow the connection diagrams below for HDAVI control of
a single AV piece of equipment such as a Panasonic DIGA-
DVD recorder, RAM theater, or Player theater system.
Refer to page 28-29 for Setup Menu settings and additional
control information.
Optional HDMI and/or optical cables are not provided.
If connection (or setting) of equipment compatible with HDAVI
control is changed, switch the power of this unit Off then On
again while the power of all equipment is On (so that the
unit can correctly recognize the connected equipment) and
check that DIGA, RAM theater, and Player theater playback
operate.
EZ Sync TM Connections
■
Setting of this unit after connection
After making connections as shown above, set “EZ Sync” (under “EZ Sync setting”) to “On” using the Setup menu.
(p. 28-29).
Note
•
HDMI 1 is recommended.
When connecting to HDMI 2, set the input mode to HDMI 2 (p. 22) initially before connecting to HDMI 2. After
connection, confirm the HDMI control functions (p. 28-29).
■
Connecting this unit to a DVD
recorder and AV amp
When using an “EZ Sync” audio-video
amplifier and a compatible DIGA recorder,
use a daisy chain connection as shown
below.
•
One AV amp and one DIGA recorder can be operated with this unit. •
Be sure to connect the AV amp between this unit and the DIGA recorder.
DIGA
(Panasonic DVD
Recorder)
HDMI
(AV IN)
■
To listen to the TV
through speakers
Amplifier
•
When equipment (STB, DVD, etc.) is connected to
HDMI or COMPONENT terminals, only audio signals
can be obtained. From the output terminals, no video
signals can be passed. •
When receiving digital channel signals, all digital
formats are down-converted to composite NTSC
video to be output through the OUTPUT terminals.
or
OPTICAL IN
or
Digital Audio out
SD Slot
or
or
■
Connecting this unit to the DIGA, RAM theater, or Player
theater
•
For DIGA: Connect with HDMI cable •
For RAM theater and Player theater:
Connect with the HDMI and audio cables.
If audio cable is not connected, you cannot listen to the TV
program through the theater system.
HDMI
(AV OUT)
Panasonic
HD Camcorder
or
Back of the TV
or or
A HDMI cable
Connect with
A
or
B
B HDMI-DVI
Conversion
cable + Audio
cable