Philips SCF260/33 - Manual (Page 5)

b
a
d
e
c
8 9
Contenido:
a. Tapa
b. Solapa de Tapa
– Se levanta para acomodar
biberones más grandes (11oz/330ml)
y biberones Tempo (8oz/236ml)
c. Base del Calentador
d. Aparato para Levantar
e. Visualizador Electrónico Interactivo
Gracias por elegir Philips AVENT
El Calentador digital de Biberones y Comida para Bebé Philips AVENT es el único calentador con la
Tecnología avanzada, diseñado para inteligente y precisamente ajustar el tiempo de calentamiento a
base del contenido y la cantidad. Si calienta leche o comida para bebé que está congelada, refrigerada o
de la temperatura ambiente, el Calentador digital de Biberones y Comida para Bebé la calentará rápida
y seguramente, y de manera uniforme – sin dejar lugares calientes. El diseño versátil sostiene todo
Biberón AVENT, Vasito VIA, Tempo y tarros de comida para bebé.
Por favor tome 5 minutos para leer el FOLLETO DE INSTRUCCIONES EN SU
TOTALIDAD, inclusive las advertencias, antes de utilizar su Calentador digital de
Biberones y Comida para Bebé por primera vez. POR FAVOR GUARDE ESTAS
INSTRUCCIONES para futura consulta.
ES
Troubleshooting Guide
Food is not
warm enough
The temperature of warmed food depends on the consistency of the food. Philips
AVENT recommends that, ideally, pureed food only should be heated with this
warmer. If you find that thicker food is not warm enough at the end of the
warming cycle, fill the warmer with an additional 1oz/30ml of water. On step
4 and 5, choose the food from room temperature mode and program the
warmer at the 1oz/30ml option. Before feeding your baby, stir the food.
Always check food temperature before feeding.
Display will not
illuminate / Warmer
will not turn on
Check that the lid is closed correctly. Check that the warmer is plugged
in correctly. Then hold the Power/Mode Selection Button for 3 seconds.
Symbols on the
display are flashing
• If the milk, room temperature and oz/ml symbols are flashing, then the lid
has not been closed correctly.
• If all volume symbols are flashing, and the warmer beeps intermittently for
30 seconds then the cycle is complete. Follow Step 8 onwards to remove the
bottle or container from the warmer.
• If all mode and starting temperature symbols are flashing, then the unit
requires de-scaling. See section ‘ Care of your Digital Bottle and Baby Food Warmer ’
on page 5. To acknowledge the de-scale warning, press and hold the Power/
Mode Selection or Volume Selection/Start Button for 3 seconds. If you do not
wish to de-scale, please be aware that this may cause irreparable damage.
The warmer
is beeping
• If oz/ml symbols flash, and the warmer beeps twice, insufficient water has been
placed in the warmer. Unplug the warmer, discard the milk or food and empty
any remaining water. Be careful as the warmer is hot. Follow instructions from
Step 1 onwards.
• If all volume symbols are flashing, and the warmer beeps intermittently for
30 seconds then the cycle is complete. Follow Step 8 onwards to remove the
bottle or container from the warmer.
To stop the
warming cycle
Press the Power/Mode Selection Button and the warmer will beep and return to
default settings.
To start the
warming cycle
Once the correct mode, starting temperature and volume have been selected,
press and hold the Volume Selection/Start Button until the warmer beeps.
If the lid is opened
during warming cycle
If the lid is opened at any time during the warming cycle, the lights on the display
panel will flash and the warmer will stop and return to default settings. In order to
reset the warmer after the lid has been opened, empty out any residual water, then
follow instructions for use from step 1 onwards. Since this could occur at any stage
of the warming cycle, milk or food should be discarded for safety reasons.
Difficulty setting the
appropriate amount of
frozen food
The maximum volume that may be selected when warming food from frozen
is 8oz/240ml.
Milk is not
warm enough
If you find that milk is not warm enough at the end of a warming cycle, fill the
warmer with an additional 1oz/30ml of water. On step 4 and 5, choose the milk
from room temperature mode and program the warmer at the 1oz/30ml option.
Before feeding your baby, shake the bottle, nurser or storage container gently
and check the temperature of the milk by sprinkling a few drops on the back
of your hand.