Audio dubbing – Panasonic AG-DVG7P User Manual
Page 38
V
V
V
V
C
C
C
C
R
R
R
R
M
M
M
M
o
o
o
o
d
d
d
d
e
e
e
e
38
V
V
V
V
C
C
C
C
R
R
R
R
M
M
M
M
o
o
o
o
d
d
d
d
e
e
e
e
Audio Dubbing
You can add music or narration to the recorded
Cassette.
O
If the tape recorded in the [16bit] Mode is dubbed
with the Audio Dubbing function, the original sound
is erased. (If you wish to preserve the original
sound, use the [12bit] Mode when recording.)
O
Audio Dubbing cannot be performed on a recording
done in LP Mode. (-18-)
To Cancel Audio Dubbing
Press the [;] Button u on the Remote Controller.
The Camera Recorder is in the Still Playback Mode
again.
To dub audio while listening to a pre-recorded
sound
When pausing the audio dubbing, [12bit AUDIO] on
the [PLAYBACK FUNCTIONS] Sub-Menu is
automatically set to [ST2] and you can check the pre-
recorded sound. When a microphone is used for audio
dubbing, use headphones to listen to the pre-recorded
sound while dubbing the audio. (When using
headphones, set [AV JACK] on the [AV IN/OUT
SETUP] Sub-Menu to [OUT].) When the line input is
used, you can dub audio while listening to a pre-
recorded sound from the speaker.
To Play Back the Sound Recorded by 12bit Audio
Dubbing
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS]
>> [12bit AUDIO] >> [ST2] or [MIX].
ST1: It plays back only the original sound.
ST2: It plays back only the sound added by Audio
Dubbing.
MIX: It plays back both the original sound and the
sound added by Audio Dubbing simultaneously.
O
For other notes concerning this item, see -45-.
1
Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP]
>> [AV JACK] >> [IN/OUT].
2
Continuing the aforesaid setup, select [A.DUB
INPUT] >> [MIC] or [AV IN].
O
Set to [AV IN] when external device is used, and
to [MIC] when an external or built-in microphone
is used.
3
Switch the Camera Recorder over to the Still
Playback Mode where you want to add new
sound.
MENU
W.B/SHUTTER/IRIS
PUSH
VOL/JOG
>
B
1
Set [VCR FUNCTIONS] >> [RECORDING SETUP]
>> [AUDIO LEVEL] >> [YES].
2
Press the [PUSH] Dial > to select the [MNL
(AGC, NO-AGC)].
O
The Audio Level Meter appears.
3
Turn the [PUSH] Dial > to increase or decrease
the bars of the [GAIN] Indication.
O
The [AUDIO LEVEL SETUP] Menu appears.
MENU
W.B/SHUTTER/IRIS
PUSH
VOL/JOG
>
B
4
Press the [A.DUB] Button i on the Remote
Controller.
5
To start Audio Dubbing, press the [;] Button u
on the Remote Controller.
STILL ADV PAUSE STILL ADV
INDEX
–
V
OL
+
STOP
INDEX
MULTI/
P-IN-P
REC
A.DUB
PLAY
C
/REW
FF/
B
i
u
$
To Adjust the Audio Level
You can adjust the Audio Level for Audio Dubbing.
AUDIO LEVEL SETUP
PUSH MENU TO RETURN
MODE AUTO MNL MNLŁ
(AGC)(NO–AGC)
(dB) –30 0 +6Ł
GAIN |||||||||||–––
O
For details, refer to the [MIC LEVEL ADJ.] on the
[RECORDING SETUP] Sub-Menu of the [CAMERA
FUNCTIONS] Main-Menu (-31-).
W.B/SHUTTER/IRIS
PUSH
VOL/JOG
>