Panasonic NV-SJ260 - Manual (Page 18)

18
If “ss” Appears under “Pos/Name” after
Entering a ShowView Number
Pos/Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under “Pos/Name”.
However, if the TV station information was not automatically
set during Preset Download or Auto Setup due to adverse
reception conditions, the “jj” indication appears instead.
In such a case, follow the operation steps below to correct it.
Press the Channel buttons :
repeatedly to select the programme
position on which the TV programme
to be recorded will be broadcast.
After you have entered the information of a TV station, it
remains stored in the VCR’s memory, and you do not need to
enter it again in the future.
To Suspend the Timer Recording Standby
Mode
When you want to use the VCR for playback, normal
recording or some other operation before the programmed
timer recording will be performed, you can temporarily
suspend the timer recording standby mode by
pressing the TIMER REC button D so that the “Á” indication
on the VCR display disappears.
However, after you have finished using the VCR, be sure
to reactivate the timer recording standby mode by pressing
the TIMER REC button D again, otherwise the programmed
timer recording will not be performed.
Note:
≥
If the VCR is not put in the timer recording standby mode at
the latest 10 minutes before the programmed timer
recording starting time, the “Á” indication flashes on the
VCR display. In this case, press the TIMER REC button D
to put the VCR in the timer recording standby mode.
To Programme with the
ShowView Function
The ShowView numbers assigned to each TV programme
and published alongside the TV programme listings in
newspapers and magazines make it extremely easy to set the
VCR for timer recording.
The duration of a timer recording programmed with
ShowView number may be slightly longer than the actual
duration of the TV programme.
Preparations
≥
Confirm that the VCR is on.
≥ Confirm that the TV is on and the VCR viewing channel is
selected.
≥ Insert a video cassette with an intact erasure prevention
tab.
≥ Set the VCR/TV switch O to “VCR”.
Example:
Programming a timer recording of a TV programme with the
ShowView number 920126
Operations
1
Press the SHOW VIEW button L to display the
menu for entering the ShowView number on the TV.
2
Press the Numeric buttons 2
to enter the ShowView
number.
≥
If you have entered a
wrong digit, press the
Cursor button (2) Q and
then enter the correct digit.
3
Press the OK button S to display the programmed
content.
≥
To extend the ending time or to make any
corrections, use the Cursor buttons (3421) Q,
the Channel buttons :, the DATE button ;, the ON
button G or the OFF button F.
≥ See page 19 for VPS/PDC recording.
4
Press the TAPE button C to select the
corresponding cassette tape length.
(See page 29.)
5
Press the OK button S again to conclude the
settings.
≥
To programme additional
timer recordings, repeat
operation steps 1–5.
6
Press the TIMER REC button D to switch the VCR
over to the timer recording standby mode.
≥
Check that “Á” is lit on the VCR display.
If it is flashing, check the timer recording details
again. (See page 19.)
ShowView
9 2 0 1 2 6
On Screen Display
Timer recording
Pos Start Stop VPS
Name DATE ON OFF SP PDC Min
ZDF 27/10 We 20:00 21:30 SP ON 90
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj
Timer recording
Pos Start Stop VPS
Name DATE ON OFF SP PDC Min
jj jjjjj 15:00 17:00 SP jjj 120
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj /jj jj jj : jj jj : jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj
jjjjj jj jj jj jj jj jj jj jj jjj jjj “jj” indication