Panasonic DMR-EX79 - Manual (Page 8)

8
RQT9306
STEP
1
Connection
≥Before connection, turn off all equipment and read the appropriate operating instructions.
≥Refer to “Additional connections” (> 66) for connection using other terminals and connection with other equipment.
You can enjoy high-quality picture by changing the connection between this unit and your TV as follows.
When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted. You can enjoy high quality, digital
video and audio with just one cord. When connecting to an HDMI-compatible HDTV (High Definition Television), the output can be switched to
1080p, 1080i or 720p HD video.
≥This unit incorporates HDMI
TM (V.1.3a with Deep Colour) technology.
≥Video sources converted to 1920k1080 resolution, while of high quality, will exhibit somewhat lower subjective image resolution than true,
native 1080p full-HD sources. See dealer for details.
≥Please use High Speed HDMI Cables that have the HDMI logo (as shown on the cover).
≥When setting video output to “1080p”, please use the HDMI cables 5.0 meters or less.
≥If you are connecting to a TV that is only compatible with 2 channel audio output, audio with 3 channels or more will be down mixed (> 81) and
output as 2 channels, even if connecting with an HDMI cable. (Some discs cannot be down mixed.)
≥You cannot connect this unit to DVI devices that are incompatible with HDCP.
For units compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection that are equipped with a digital DVI input
terminal (PC monitors, etc.):
Depending on the unit, images may not be displayed properly or at all when connecting with a DVI/HDMI switching cable. (Audio cannot be
output.)
When the unit is not to be used for a long time
To save power, unplug it from the household
mains socket. This unit consumes a small
amount of power, even when it is turned off
[approx. 2 W (“Power Save” is set to “On”)]
Connecting to a television with 21-pin Scart terminal
You can also connect with the AV1 terminal on this unit using the 21-pin Scart cable.
≥If your television is equipped with RGB input capability, by connecting with a fully
wired 21-pin Scart cable you can see video using RGB output on this unit.
“AV1 Output” in the Setup menu (> 63)
Connecting a television
Required setting
Connecting to a TV with an HDMI (High Definition Multimedia Interface) cable
Regarding VIERA Link “HDAVI Control TM ” function
When connecting with a Panasonic TV (VIERA) or a receiver equipped with the “HDAVI Control” function, linked operations would be possible.
[> 36, Linked operations with the TV (VIERA Link “HDAVI Control TM ”)]
≥Non-HDMI-compliant cables cannot be utilised.
≥It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG10 (1.0 m), RP-CDHG15 (1.5 m), RP-CDHG20 (2.0 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m), etc.
RF RF
IN
IN
RF RF
OUT OUT
AV2 (EXT)
AV1
(TV)
OPTICAL
DIGI DIGITAL AL AUDIO OU UDIO OUT
(PCM/BITSTREAM) (PCM/BITSTREAM)
COMPONENT COMPONENT
VIDEO OUT VIDEO OUT S-VIDEO VIDEO R-AUDIO-L
P R
P B
Y
AC IN
OUTO U T
A V4 IV 4 I N
AV OUT
VHF/UHF
RF IN
2
1 2 4 3
AUDIO IN
R L
VIDEO IN
To the aerial
Television’s rear panel
Aerial cable
RF coaxial cable
(included)
This unit’s rear panel
To household mains socket
(AC 220 to 240 V, 50 Hz)
AC mains lead
(included)
Connect only after all other
connections are complete.
Cooling fan
Other connections
(> below, 66)
Audio/Video cable
(included)
≥Connect to terminals of the same colour.
RF RF
IN
IN
RF RF
OUT
OUT
AV2 ( EXT )
A V 1 ( TV )
OPTICAL
DIGI DIGI T T AL AL A A UDIO OU UDIO OU T T
(PCM/BITSTREAM) (PCM/BITSTREAM)
COMPONENT COMPONENT
VIDEO OUT VIDEO OUT
P R
P B
Y
A C IN
AV OU V OUT S-VIDEO VIDEO R- A UDIO- L
OUT O U T
A A V4 I V 4 I N N
HDMI AV OUT
HDMI IN
This unit’s
rear panel
HDMI cable
Television’s rear panel
≥Set “Digital Audio Output” to “HDMI and
Optical” (> 63).
(The default setting is “HDMI and Optical”.)
Required setting
Note
DMREX79GN-RQT9306-L_eng.book 8 ページ ２００９年３月２４日 火曜日 午後２時３８分