Panasonic KX-FT934HK - Manual (Page 27)

8. Programmable Features
27
Code #13: Setting the dialling mode
DIALLING MODE
=TONE [ ±]
See page 10 for details.
Code #17: Setting the ringer type for outside calls
EXT RINGER TYPE
=RINGER 1 [ ±]
To set the ringer type from one of 3 types for outside
calls. You can select “
RINGER 1” (default), “RINGER 2”
or “ RINGER 3”.
8.3 Advanced features
See page 26 for how to enter advanced feature
programming.
Code #22: Setting the journal report to print
automatically
AUTO JOURNAL
=ON [ ±]
“ ON” (default): The unit will print a journal report
automatically after every 30 new fax transmissions and
receptions (page 18).
“
OFF”: The unit will not print a journal report, but will
keep a record of the last 30 fax transmissions and
receptions.
Code #23: Sending documents overseas
OVERSEAS MODE
=ERROR [ ±]
If you cannot send a fax overseas even if the number is
correct and the line is connected, activate this feature
before sending the fax.
This feature improves the reliability by reducing the
transmission speed.
“
ERROR” (default): When the previous fax transmission
fails and you wish to re-send the document.
“
NEXT FAX”: This setting is effective only for the next
attempted fax transmission. After transmission, the unit
will return to the previous setting.
“
OFF”: Deactivates this feature.
Note:
L This feature is not available for broadcast
transmission.
L Calling charges may be higher than usual.
Code #25: Sending a fax at a specific time
DELAYED SEND
=OFF [ ±]
This feature allows you to take advantage of low-cost
calling hours offered by your telephone company. This
feature can be set up to 24 hours in advance of the
desired time.
To send a document:
1. Insert the document.
2. If necessary, press {A} or {B} repeatedly to select
the desired resolution (page 18).
3. Press {MENU}.
4. Press {#} then {2}{5}.
5. Press {A} or {B} repeatedly to select “ ON”.
6. Press {SET}.
7. Enter the fax number.
8. Press {SET}.
9. Enter the transmission start time.
L If you select 12-hour time entry when you set the
date and time (page 10), press {*} repeatedly to
select “
AM” or “PM”.
L If you selected 24-hour time entry when you set
the date and time (page 10), the time is set using
24-hour time entry.
10. Press {SET}.
11. Press {MENU}.
Note:
L To cancel after programming, press {STOP} then
{
SET}.
Code #26: Setting the Caller ID list to print
automatically
AUTO CALL. LIST
=OFF [ ±]
“ ON”: The Caller ID list will be printed automatically each
time the unit logs 30 different callers (page 15).
“
OFF” (default): The Caller ID list will not be printed, but
the unit will keep a record of the information for the last
30 different callers.
Code #31: Activating the Distinctive Ring feature
DISTINCTIVE RING
=OFF [ ±]
See page 24 for details.
Code #36: Receiving oversized documents
RCV REDUCTION
=ON [ ±]
To slightly reduce the received fax image when printing,
so that the received document will be approximately the
same length as the original document.
“
ON” (default): The received fax image will be printed
slightly smaller than the original image.
“
OFF”: Deactivates this feature. The received fax image
will be printed at the same size as the original image.
Note:
L A slight margin will be added to the printed
documents, and therefore if this feature is turned
OFF, the received document will be slightly longer
than the original document.
FT932_934HK-PFQX2561YA-en.book Page 27 Monday, May 8, 2006 5:05 PM